Business Community > Controllers > SDN Omada Controller migration - devices stay disconnected
< Controllers

SDN Omada Controller migration - devices stay disconnected

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

SDN Omada Controller migration - devices stay disconnected

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
SDN Omada Controller migration - devices stay disconnected
SDN Omada Controller migration - devices stay disconnected
2023-12-14 10:03:47 - last edited 2023-12-20 01:36:27
Tags: #Migration
Model: Omada Software Controller (Linux)  
Hardware Version:
Firmware Version: 5.12.7

Hi all,

 

I'm running the Omada controller within a docker container. As I migrate my docker containers to a new host, I want to migrate the Omada controller as well.

I followed this instructions: https://www.tp-link.com/de/support/faq/3589/

But unfortunately the devices stay in the DISCONNECTED state on both controllers. I already waited 1h, with no change.

 

Has someone a clue, what is wrong here or how I can do further troubleshooting?

 

Thanks

tukane

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:SDN Omada Controller migration - devices stay disconnected-Solution
2023-12-19 12:52:27 - last edited 2023-12-20 01:36:27

  @Virgo

 

OK, I've managed the migration now. 

I used another template to setup the docker container for the controller. This used some high-ports which where needed for discover of the devices. 

 

Thank you for your support.

Recommended Solution
  0  
  0  
#7
Options
7 Reply
Re:SDN Omada Controller migration - devices stay disconnected
2023-12-15 06:34:40

  @tukane 

 

So you have migrated it and it works, but devices are all disconnected on the controller, right? reboot?

Are devices working still? Can you ping them from the controller?

Just striving to develop myself while helping others.
  0  
  0  
#2
Options
Re:SDN Omada Controller migration - devices stay disconnected
2023-12-15 07:58:53

  @Virgo 

Yes, all steps of the migration were successful (but basicly it was just a config restore on a new controller so far). I skipped only the last step, de-attaching the devices from the old controller.

The devices are pingable from the new controller. A reboot didn't solve the problem. I can cancel the migration on the old controller and all devices are connected again. During the migration the devices work without any interuption. I'm not sure what should happen in the migration phase. Maybe the controller IP is changed in the config and the devices should perform a reboot? This is not happening.

 

Both contollers have the same software version (5.12.7). They are in the same subnet. I tried to migrate only 1 device but with same result. 

  0  
  0  
#3
Options
Re:SDN Omada Controller migration - devices stay disconnected
2023-12-18 03:32:59

  @tukane 

 

Tried to forget all devices on the old controller, and put the new controller into the network, readopt all devices on the new controller. Pay attention to the device account on the old controller, you will need it.

Just striving to develop myself while helping others.
  0  
  0  
#4
Options
Re:SDN Omada Controller migration - devices stay disconnected
2023-12-18 09:24:19

 

@Virgo 

 

I don't know if it is a good idea to forget the devices on the old controller unless they are visible and connected at the new one.

 

omada controller forget devices

 

 

 

  0  
  0  
#5
Options
Re:SDN Omada Controller migration - devices stay disconnected
2023-12-19 02:50:09

  @tukane 

 

Yes, Forget means all devices will go back to standalone mode. Be careful to back up all settings before you do it, but it indeed has a risk, it's up to you.

Just striving to develop myself while helping others.
  0  
  0  
#6
Options
Re:SDN Omada Controller migration - devices stay disconnected-Solution
2023-12-19 12:52:27 - last edited 2023-12-20 01:36:27

  @Virgo

 

OK, I've managed the migration now. 

I used another template to setup the docker container for the controller. This used some high-ports which where needed for discover of the devices. 

 

Thank you for your support.

Recommended Solution
  0  
  0  
#7
Options
Re:SDN Omada Controller migration - devices stay disconnected
2023-12-20 01:38:44

  @tukane 

 

Oh, so the old one blocked some necessary ports which the controller used, definitely, I forgot that. yes

Just striving to develop myself while helping others.
  0  
  0  
#8
Options

Information

Helpful: 0

Views: 873

Replies: 7

Tags

Migration
Related Articles
Omada SDN Controller - Upgrade Issues
519 0
Migration from Cloud Controller to OC200
200 0
Omada SDN, TL-R605, and Camera Devices Fixed IP Problem
1299 0
Omada SDN on Raspberry pi
3810 0
OC200 Controller Migration to Software Controller Error
752 0
 Omada SDN Controller - Packaging Inconsistencies
348 15
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.