Business Community > Switches > Disabling just the POE on a port so I can plug a non poe device into my switch.
< Switches

Disabling just the POE on a port so I can plug a non poe device into my switch.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Disabling just the POE on a port so I can plug a non poe device into my switch.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Disabling just the POE on a port so I can plug a non poe device into my switch.
Disabling just the POE on a port so I can plug a non poe device into my switch.
2024-01-25 18:57:09 - last edited 2024-02-02 06:12:20
Tags: #PoE
Model: SG2008P  
Hardware Version:
Firmware Version:

I had a bad experience a while back with a Unifi poe switch when I plugged in a netgear hotspot into its ethernet port that had POE, the hotspot fried, had to buy a new expencive hotspot.   So Im gunshy about plugging anything other than POE devices into these new switches.   Is there a way to just turn off the POE power on a port via Omada?   I see the disable choice per port, but it appears to disable the whole port so it doesn't pass packets either.  -Bill

Bill http:\\cowlesmountain.com Traveling the USA in a 40' Bus
  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Disabling just the POE on a port so I can plug a non poe device into my switch. -Solution
2024-01-26 01:16:15 - last edited 2024-02-02 06:12:22

Hi @BigBillSD 

Thanks for posting in our business forum.

There is a PoE management for the multiple ports model. If you are using the controller, you can disable it in the click switch > Config > Port Config. That'll turn off the PoE on the port.

 

About the PoE, I'd like to comment that our switch is IEEE 802.3 standard PoE. I am not sure why would your device get fried but if it is standard PoE, it does not supply power directly to the device but tests its power specs with a minimum voltage and amp.

So far, I have not experienced or seen any cases of 802.3 would fry a device. You might take a look at the specs of your device and see how it works if it needs proper grounding and such.

 

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
Recommended Solution
  1  
  1  
#2
Options
Re:Disabling just the POE on a port so I can plug a non poe device into my switch. -Solution
2024-01-29 02:08:41 - last edited 2024-02-02 06:12:20

Hi @BigBillSD 

Thanks for posting in our business forum.

If you are doing something further click on that page

 

Or this page.

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
Recommended Solution
  1  
  1  
#4
Options
3 Reply
Re:Disabling just the POE on a port so I can plug a non poe device into my switch. -Solution
2024-01-26 01:16:15 - last edited 2024-02-02 06:12:22

Hi @BigBillSD 

Thanks for posting in our business forum.

There is a PoE management for the multiple ports model. If you are using the controller, you can disable it in the click switch > Config > Port Config. That'll turn off the PoE on the port.

 

About the PoE, I'd like to comment that our switch is IEEE 802.3 standard PoE. I am not sure why would your device get fried but if it is standard PoE, it does not supply power directly to the device but tests its power specs with a minimum voltage and amp.

So far, I have not experienced or seen any cases of 802.3 would fry a device. You might take a look at the specs of your device and see how it works if it needs proper grounding and such.

 

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
Recommended Solution
  1  
  1  
#2
Options
Re:Disabling just the POE on a port so I can plug a non poe device into my switch.
2024-01-26 13:21:35

  @Clive_A   Are you saying that if I disable that port via the Omada interface, only POE is disabled on that port?  It looks like packet forwarding thru that port was disabled also.   -Bill

Bill http:\\cowlesmountain.com Traveling the USA in a 40' Bus
  0  
  0  
#3
Options
Re:Disabling just the POE on a port so I can plug a non poe device into my switch. -Solution
2024-01-29 02:08:41 - last edited 2024-02-02 06:12:20

Hi @BigBillSD 

Thanks for posting in our business forum.

If you are doing something further click on that page

 

Or this page.

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
Recommended Solution
  1  
  1  
#4
Options

Information

Helpful: 0

Views: 2036

Replies: 3

Tags

PoE
Related Articles
 POE Recovery
1466 0
TL-SG2210P + Omada not reporting PoE port status, cannot do PoE Recovery
685 0
POE port showing 100 mbps which is connected to EAP 115 accesspoint
478 0
 non POE device is not working via POE port
675 0
POE Does Not Work
942 0
POE working but the POE LED dount indicate it
461 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.