Home

Forums

Stories

Knowledge Base

Business Community > Controllers > Is there any way to show IPv6 address in client page?

< Controllers

Is there any way to show IPv6 address in client page?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Is there any way to show IPv6 address in client page?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ceejaybassist

2024-03-13 11:13:06

Posts: 83

Helpful: 41

Solutions: 1

Stories: 0

Registered: 2023-07-17

Is there any way to show IPv6 address in client page?

2024-03-13 11:13:06

Model: OC200

Hardware Version: V1

Firmware Version: 1.29.3 Build 20240131 Rel.35531

Now that the EAP225-Outdoor Pre-release firmware supports IPv6, is there a way to display the wired client's assigned IPv6 address (both local and public) on the client page?

Those inside yellow boxes are wired clients.

Gateway: ER605 v2 2.2.4 Build 20240119 Rel.44368
Controller: OC200 v1 1.29.3 Build 20240131 Rel.35531

3 Reply

Hank21

2024-03-14 09:40:07

Posts: 3673

Helpful: 718

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:Is there any way to show IPv6 address in client page?

2024-03-14 09:40:07

@ceejaybassist

Can you confirm whether Wired clients are assigned IPv6 addresses? Can IPv6 addresses be displayed for wireless clients? Is your router an Omada router?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

ceejaybassist

LV2

2024-03-14 11:56:11 - last edited 2024-03-14 12:03:05

Posts: 83

Helpful: 41

Solutions: 1

Stories: 0

Registered: 2023-07-17

Re:Is there any way to show IPv6 address in client page?

2024-03-14 11:56:11 - last edited 2024-03-14 12:03:05

@Hank21 Yes. All wired clients/devices support IPv6 (except OC200 maybe?) and I can confirm that they are getting an IPv6 address. However, their IPv6 address is not showing in the IPv6 pane in the client page. As you can see from the photo above, only the clients connected to my EAP225-Outdoor (early access firmware) are displaying their IPv6 addresses in the IPv6 pane of the client page. My gateway is Omada ER605 v2.

Hank21

2024-03-20 09:58:45

Posts: 3673

Helpful: 718

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:Is there any way to show IPv6 address in client page?

2024-03-20 09:58:45

@ceejaybassist

To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID240339276. please check your email box and ensure the support email is well received. Thanks!

Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.

Many thanks for your great cooperation and patience!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Is there any way to show IPv6 address in client page?

Is there any way to show IPv6 address in client page?

Information

Voters 0

Tags