What is best way to replace router in Omada setup with OC200?

What is best way to replace router in Omada setup with OC200?

What is best way to replace router in Omada setup with OC200?
What is best way to replace router in Omada setup with OC200?
2024-07-17 08:09:20 - last edited 2024-07-19 02:10:54
Model: OC200  
Hardware Version:
Firmware Version:

Hi,

 

I have a whole house network with 4APs, 2 switches, OC200, and a router (ER7206).
What is important is that I have a switch connected to the router. And that switch powers all APs and OC200 is also connected to this switch.

I didn't change a management VLAN (don't want to repeat factory resetting all stuff due to my inability to set it up correctly).
Not sure if this is important, but I have DHCP reservations set for switches.
OC200 has static IP set.

 

I want to slowly switch to 2,5 Gbps and I got myself ER707-M2 router.

 

What is the best and most painless approach to switch out router?

  0      
  0      
#1
Options
1 Accepted Solution
Re:What is best way to replace router in Omada setup with OC200?-Solution
2024-07-18 07:55:54 - last edited 2024-07-19 02:10:54

  @Hooch 

To begin with, please log into the web interface of the ER707-M2 and edit the LAN. Since the default LAN is 192.168.0.1, you should change it to match your current LAN. Following that, you can connect the ER707-M2 while replacing the ER-706. After that, you can use the web interface login credentials to adopt the ER707-M2 to the controller. Additionally, don't forget to configure the controller-managed switches and APs to static IP addresses.

How to add an Omada Gateway to the network?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
3 Reply
Re:What is best way to replace router in Omada setup with OC200?-Solution
2024-07-18 07:55:54 - last edited 2024-07-19 02:10:54

  @Hooch 

To begin with, please log into the web interface of the ER707-M2 and edit the LAN. Since the default LAN is 192.168.0.1, you should change it to match your current LAN. Following that, you can connect the ER707-M2 while replacing the ER-706. After that, you can use the web interface login credentials to adopt the ER707-M2 to the controller. Additionally, don't forget to configure the controller-managed switches and APs to static IP addresses.

How to add an Omada Gateway to the network?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:What is best way to replace router in Omada setup with OC200?
2024-07-18 08:14:22

  @Hank21 Will it not adapt if I don't change LAN settigns on new router?

  0  
  0  
#3
Options
Re:What is best way to replace router in Omada setup with OC200?
2024-07-19 02:10:38

  @Hooch 

Since your OC200's IP address is not located on the same subnet as the router—192.168.0.1 is its default IP address—it is unable to locate the router directly.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options