R600VPN Config
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
R600VPN Config
Model :
Hardware Version : Not Clear
Firmware Version :
ISP :
I have a pair of R600VPN routers. I have connectivity between the 2 units via the WAN interface via the IPSEC tunnel ( as verified via the traceroute - no intermediate link). I want to route all treffic from one VPN router to the other VPN router, to be routed to a separate internet connection. All traffic via site 'B' will royter via site 'A' and then default route to the Internet via site 'A'. I want to understand how the default routes and static routes need to be configured to achieve this.
Site 'A'
Local subnet 192.168.1.0/24
Default router 192.168.1.1 (route to the Internet router)
Local LAN VPN router LAN address 192.168.1.2
WAN - 1.1.1.1
Site 'B'
Local subnet 192.168.2.0/24
local LAN VPN router LAN address 192.168.2.1
WAN 2.2.2.2
Hopefully someone can point me in the correct direction
Thanks
Pete
Hardware Version : Not Clear
Firmware Version :
ISP :
I have a pair of R600VPN routers. I have connectivity between the 2 units via the WAN interface via the IPSEC tunnel ( as verified via the traceroute - no intermediate link). I want to route all treffic from one VPN router to the other VPN router, to be routed to a separate internet connection. All traffic via site 'B' will royter via site 'A' and then default route to the Internet via site 'A'. I want to understand how the default routes and static routes need to be configured to achieve this.
Site 'A'
Local subnet 192.168.1.0/24
Default router 192.168.1.1 (route to the Internet router)
Local LAN VPN router LAN address 192.168.1.2
WAN - 1.1.1.1
Site 'B'
Local subnet 192.168.2.0/24
local LAN VPN router LAN address 192.168.2.1
WAN 2.2.2.2
Hopefully someone can point me in the correct direction
Thanks
Pete
Re:R600VPN Config
alphhha - I get an error message when I try to add 0.0.0.0/32 in router 'A'.
Error code: 34011 Peer subnet is not correct.
I have attached an amended diagram. I can ping the 192.168.1.227, router A from 192.168.2.1, router B and the same in reverse. Router B can not ping the Internet router 192.168.1.1. I have a static route in the Internet router ponting 192.168.2.0/24 to 192.168.1.227/ Other devices on the 192.168.1.0/24 LAN can not ping 192.168.2.1, Any suggestions what I am missing
Error code: 34011 Peer subnet is not correct.
I have attached an amended diagram. I can ping the 192.168.1.227, router A from 192.168.2.1, router B and the same in reverse. Router B can not ping the Internet router 192.168.1.1. I have a static route in the Internet router ponting 192.168.2.0/24 to 192.168.1.227/ Other devices on the 192.168.1.0/24 LAN can not ping 192.168.2.1, Any suggestions what I am missing
Re:R600VPN Config
I have continued with my testing and have made progress, but I am not to the required configuration.
I have added a new graphic for further clarification
From PC A, I can ping PC B and PC B and ping PC A as well as the gateways. PC B can ping 192.168.1.1. I can ping the internet from PC A (8.8.8.8 - Google DNS). However, I can not ping the Internet from PC 'B'. I added a static route in router B 8.0.0.0/8 to 192.168.1.1 (Internet router) as well as router A address (192.168.1.227). neither of these worked.
Any thoughts? I would like to get working by next week, when I need to install the solution at its permanent location.
I have added a new graphic for further clarification
From PC A, I can ping PC B and PC B and ping PC A as well as the gateways. PC B can ping 192.168.1.1. I can ping the internet from PC A (8.8.8.8 - Google DNS). However, I can not ping the Internet from PC 'B'. I added a static route in router B 8.0.0.0/8 to 192.168.1.1 (Internet router) as well as router A address (192.168.1.227). neither of these worked.
Any thoughts? I would like to get working by next week, when I need to install the solution at its permanent location.