Business Community > Routers > R600VPN internal server via external IP.
< Routers

R600VPN internal server via external IP.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

R600VPN internal server via external IP.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
R600VPN internal server via external IP.
R600VPN internal server via external IP.
2015-12-02 23:38:28 - last edited 2021-08-21 05:34:04
Model : TL-R600VPN

Hardware Version :

Firmware Version :

ISP :

So just replaced my dead Netgear with an R600VPN. Everything is up and working fine, except I cannot access my local servers via my external static IP. For example, I can connect to my Teamspeak server via its local IP, but if I try to connect using my domain name or external IP, then it times-out, however, everyone outside my network can connect perfectly fine.
  0      
 
  0      
 
#1
Options
6 Reply
Re:R600VPN internal server via external IP.
2015-12-07 15:34:10 - last edited 2021-08-21 05:34:04
It is because the R600VPN does not support NAT Lookback.
  0  
  0  
#2
Options
Re:R600VPN internal server via external IP.
2015-12-07 16:17:40 - last edited 2021-08-21 05:34:04

jery wrote

It is because the R600VPN does not support NAT Lookback.


Thanks for the reply. That's what what I'm after. So my options in this seem somewhat limited, I either need a DNS server on my network, or find a router with NAT Loopback? Any suggestions?
  0  
  0  
#3
Options
Re:R600VPN internal server via external IP.
2015-12-28 19:54:10 - last edited 2021-08-21 05:34:04
Hi Anach， what is the hardware version of your R600VPN? I have a R600VPN, its hardware version is 2, it support NAT lookback as I tested
  0  
  0  
#4
Options
Re:R600VPN internal server via external IP.
2015-12-29 07:20:50 - last edited 2021-08-21 05:34:04
Hi Ada, I have been in contact with support, whom have confirmed NAT Loopback is supported (hardware version 2), but I am unable to get it to function on my network. So currently we're trying to work out why, as it works fine when I plugin a Netgear.
  0  
  0  
#5
Options
Re:R600VPN internal server via external IP.
2016-01-01 05:19:06 - last edited 2021-08-21 05:34:04
Further testing. I tested WNDR4500, WNDR3800, TL-W350G, all working fine with loopback both TCP/UDP ports. Testing with R600VPN has confirmed that TCP NAT loopback is functioning as expected, however, UDP NAT loopback is not, no matter what ports or service I try to enable.
  0  
  0  
#6
Options
Re:R600VPN internal server via external IP.
2016-01-09 09:42:58 - last edited 2021-08-21 05:34:04
I upgraded to an ER604W, which also works fine with NAT Loopback, but unfortunately I had to setup a repeater as it didn't recognise the 15m cat5 cable for some reason, which all other's had no problems with.
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1509

Replies: 6

Related Articles
 access internal server with external address
3688 0
 limit specific IP to access to internal server
869 0
Public IP shows same IP as Internal Network
912 1
 Routing external IP to internal IP using 2 WANs (like 2 webservers)
911 0
Blocking/Allowing public access to server via IP Groups
1094 0
No login via IP
285 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.