Business Community > WiFi > Business Wilreless configuration.
< WiFi

Business Wilreless configuration.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Business Wilreless configuration.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Business Wilreless configuration.
Business Wilreless configuration.
2017-06-17 21:46:09
Model :

Hardware Version :

Firmware Version :

ISP :

Hi folk good morning, I'm here because I need help to build a wireless network in my workplace.
The building is a Car Dealership, and we have a parking lot, and we need wifi in all area of the space.
My project to build was 6 items, and I already bought almost of them.

1 T1500G 10MPS FOR POE

4 EAP 220 CEILING MOUNT

1 EAP 110- OUTDOOR.

MY PLANS IS TO USE THE COMCAST ROUTER IN BRIDGE, BECAUSE IS HORRIBLE, TO MANAGE ACCESS AND CONFIGURE.
Witch configuration I have to setup at the T1500G to receive the internet and router to all other devices include the EAP220 access point.
Or i need to buy an extra router like TL-R480T+, to setup the internet and share with the T1500G.
  0      
 
  0      
 
#1
Options
6 Reply
Re:Business Wilreless configuration.
2017-07-17 11:02:48
Topology is simple as: Internet--- Router---T1500G---EAPs, I think this should be ok if you have no special requirement, no need for TL-R480T+.
Besides, you can share with us that do you have any requirements like dividing the network into different VLAN, if no special requirements, I also think there is no need for extra configuration on the T1500G.
  0  
  0  
#2
Options
Re:Business Wilreless configuration.
2017-07-20 06:28:17
No, it's a normal Network, we have almost 37 devices connected, wireless and cable, the wired cable is gigabit, and the internet provider are comcast, 200mbps down and 35 up.
I asked about the TL-R480T, because the comcast cable modem are the worst to control the IP and DHCP, and my option is to use the comcast modem as bridge and setup the TL-R480T to manage all , my connection some times is slow. Maybe in the future I rather to put another internet to help.

  0  
  0  
#3
Options
Re:Business Wilreless configuration.
2017-07-20 17:02:52
If you want to use comcast modem as bridge, then I think you have to buy an extra NAT router.
While since TL-R480T+ adopts fast Ethernet port, and its NAT throughput is within 100Mbps, so it might not meet your speed of 200mbps down and 35 up. You can choose TL-ER5120 with an NAT throughput of 350Mbps instead.
  0  
  0  
#4
Options
Re:Business Wilreless configuration.
2017-07-21 01:50:18
Just a question, can I use the EAP controler to receive the internet from the comcast bridge modem, and control trough, T1500G ?
  0  
  0  
#5
Options
Re:Business Wilreless configuration.
2017-07-21 08:46:00
EAP controller adopts hang-side network, so it's just used to manage and monitor the EAPs in network.
The EAP controller has no NAT and DHCP function, you can not use it as a router to receive the Internet and share with devices behind.
  0  
  0  
#6
Options
Re:Business Wilreless configuration.
2017-07-25 23:05:51
Ok thanks, for now I setup the basic, install all eaps, and the 1500 10mp, Next week, i will finish all, It's working pretty good and was easy to setup.
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1006

Replies: 6

Related Articles
 Small Business Setup Configuration
606 0
 Proper Configuration for Guests in a Business Network
437 0
 Service, Support for Configuration of Business Facebook WIFI
382 0
Business equipment support
298 0
Network Design for Small Business
850 0
 EAP660 for a small business?
666 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.