Can't disable interface eg. WAN/LAN3 with omada controler on ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can't disable interface eg. WAN/LAN3 with omada controler on ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can't disable interface eg. WAN/LAN3 with omada controler on ER605
Can't disable interface eg. WAN/LAN3 with omada controler on ER605
2022-07-06 07:48:06 - last edited 2022-07-06 10:18:04
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version: 1.2.1

Trying to disable interface for LAN (DEFAULT) network on ER605 witch omada software controller 5.3.1.

 

Getting "The interface of Default LAN cannot be modified.".

 

So - how to protect router ports same way as switch ports can be disabled (eg. TL-SG2008P) ?

  0      
  0      
#1
Options
2 Accepted Solutions
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605-Solution
2022-07-06 08:27:03 - last edited 2022-07-06 10:18:08

  @lacrimal 

 

There is only one way to lock default LAN on this routers..

 

Recommended Solution
  0  
  0  
#2
Options
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605-Solution
2022-07-06 09:44:16 - last edited 2022-07-06 10:18:04

  @lacrimal 

 

yes and no, you can not disable any ports on the router when using Omada SDN controller, you can also not change on deafult LAN, you must do so the router must run in stand alone mode. I have blinded these ports with a blind lid without a key so that no one connects anything by mistake,  :-)

 

I use this, this is chep

Recommended Solution
  0  
  0  
#4
Options
5 Reply
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605-Solution
2022-07-06 08:27:03 - last edited 2022-07-06 10:18:08

  @lacrimal 

 

There is only one way to lock default LAN on this routers..

 

Recommended Solution
  0  
  0  
#2
Options
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605
2022-07-06 09:32:02
you are sarcastic :-) ?
  0  
  0  
#3
Options
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605-Solution
2022-07-06 09:44:16 - last edited 2022-07-06 10:18:04

  @lacrimal 

 

yes and no, you can not disable any ports on the router when using Omada SDN controller, you can also not change on deafult LAN, you must do so the router must run in stand alone mode. I have blinded these ports with a blind lid without a key so that no one connects anything by mistake,  :-)

 

I use this, this is chep

Recommended Solution
  0  
  0  
#4
Options
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605
2022-07-06 10:17:07 - last edited 2022-07-06 10:17:56

So ... wax or silicone plumb :-)

Seriously

 

@Fae 

can you put this to wishlist ? Omada SDN still not cover mass of available functions. Last time reported not distinguishable ports on ER605.

  0  
  0  
#5
Options
Re:Can't disable interface eg. WAN/LAN3 with omada controler on ER605
2022-07-11 09:54:11
TP-link Can we put this to Requests & Suggestions ?
  0  
  0  
#6
Options