Switch ACL's no longer working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Switch ACL's no longer working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Switch ACL's no longer working
Switch ACL's no longer working
2023-05-05 13:31:03 - last edited 2023-05-08 03:09:25

The following Switch ACL doesn't want to work anymore under my current configuration (shown in my signature)

 

 

The intent behind this rule is to disable internet access  to hsIOT (normally by time range but for the purposes of testing I have am not using the time range).  The ACL binding is by VLAN (hsIOT-E) but I also tried port binding to all ports, doesn't make a difference..  I tried force provisioning all devices... no go.  I am not quite sure when this broke but I recently upgraded to ER605  V1.2.3 Beta and the latest Omada Controller version.  I have since gone back to the V1.2.2 Feb BETA that was working fine but no difference now :(

 

Here is the list of my networks along with the GATEWAYS IP GROUP.

 

OmadaLinux v5.13.10 R605 V1:1.3.0 - Build 20230511 R.51317 SG2008P V1:V1.0.8 Build 20230602 R.73473 SG2008P V3:V3.0.5 Build 20230602 R.73473 3 x EAP245 V3:V5.1.0-Build 20230104 R.79433
  0      
  0      
#1
Options
1 Accepted Solution
Re:Switch ACL's no longer working-Solution
2023-05-08 03:04:06 - last edited 2023-05-08 03:09:25
Rebooting the switch seems to have fixed the problem. I should have known better and tried that. Thought force provisioning would have been even better Thanks for the tip 👍🙂
OmadaLinux v5.13.10 R605 V1:1.3.0 - Build 20230511 R.51317 SG2008P V1:V1.0.8 Build 20230602 R.73473 SG2008P V3:V3.0.5 Build 20230602 R.73473 3 x EAP245 V3:V5.1.0-Build 20230104 R.79433
Recommended Solution
  2  
  2  
#4
Options
2 Reply
Re:Switch ACL's no longer working
2023-05-06 06:45:01

  @TandS 

 

Have you tried rebooting switches to test?

 

TandS wrote

 I have since gone back to the V1.2.2 Feb BETA that was working fine but no difference now :(

 

Do you mean this issue can be fixed by downgrading the firmware to 1.2.2?

Just striving to develop myself while helping others.
  0  
  0  
#2
Options
Re:Switch ACL's no longer working-Solution
2023-05-08 03:04:06 - last edited 2023-05-08 03:09:25
Rebooting the switch seems to have fixed the problem. I should have known better and tried that. Thought force provisioning would have been even better Thanks for the tip 👍🙂
OmadaLinux v5.13.10 R605 V1:1.3.0 - Build 20230511 R.51317 SG2008P V1:V1.0.8 Build 20230602 R.73473 SG2008P V3:V3.0.5 Build 20230602 R.73473 3 x EAP245 V3:V5.1.0-Build 20230104 R.79433
Recommended Solution
  2  
  2  
#4
Options

Information

Helpful: 0

Views: 756

Replies: 2

Related Articles