TL-WA5210G I think I have have Flashed firmware for V2 on V1 hardware. You are my last hope
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-WA5210G I think I have have Flashed firmware for V2 on V1 hardware. You are my last hope
Model : TL-WA5210G
Hardware Version : v1
Firmware Version : was upgrading to 111209
ISP :
So this happened 5-6 months ago and I tried updating firmware on my TL-WA5210G.
I was not attentive and chose 1.2 is version 2 h/w in firmware download or something went wrong during f/w upgrade
Long story short I can only see that power LED is on now. After much research in last couple of months I was able to get serial console by soldering into UART terminals inside :)
connecting USB-TTL to my MAC and setting baud rate to 38400 I am only able to get this repetitive response and device gets restarted every 10 seconds.
[CODE]
sh-3.2# cu --parity=none -s 38400 -l /dev/tty.SLAB_USBtoUART
Connected.
AR2315 rev 0x00000086 startup...
panic: romStart failed!
sysConsoleDump: type 0x10400000
epc: 0xfffeefbf bva: 0x137aad2a sr: 0x10400000 cse: 0xb080007c
R0: r0: 0x00000000 at: 0xbfc00000 v0: 0xffffffff v1: 0x805916e0
R4: a0: 0xbfc00a07 a1: 0xb1100000 a2: 0x00000000 a3: 0x80594eff
R8: t0: 0x00000040 t1: 0x00000020 t2: 0x80594ef7 t3: 0x805916f8
R12: t4: 0x00000000 t5: 0x0000000d t6: 0x47e3a63c t7: 0x4c75a632
R16: s0: 0x00000002 s1: 0xbf9e5b5f s2: 0xffd3ffd8 s3: 0xfffaf346
R20: s4: 0xf3aafd8f s5: 0xb3efbd59 s6: 0xd774ddcf s7: 0xdfff31df
R24: t8: 0x00000001 t9: 0x805916d8 k0: 0x00000000 k1: 0x00000000
R28: gp: 0x80598630 sp: 0x8047fff0 fp: 0x5fffaf49 ra: 0xbfc00a28
[/CODE]
I know 5210G is now end of life, but I dont want to part with my sleek CPE yet.
Any hopes of reviving this ? or its a dump now ?
Hardware Version : v1
Firmware Version : was upgrading to 111209
ISP :
So this happened 5-6 months ago and I tried updating firmware on my TL-WA5210G.
I was not attentive and chose 1.2 is version 2 h/w in firmware download or something went wrong during f/w upgrade
Long story short I can only see that power LED is on now. After much research in last couple of months I was able to get serial console by soldering into UART terminals inside :)
connecting USB-TTL to my MAC and setting baud rate to 38400 I am only able to get this repetitive response and device gets restarted every 10 seconds.
[CODE]
sh-3.2# cu --parity=none -s 38400 -l /dev/tty.SLAB_USBtoUART
Connected.
AR2315 rev 0x00000086 startup...
panic: romStart failed!
sysConsoleDump: type 0x10400000
epc: 0xfffeefbf bva: 0x137aad2a sr: 0x10400000 cse: 0xb080007c
R0: r0: 0x00000000 at: 0xbfc00000 v0: 0xffffffff v1: 0x805916e0
R4: a0: 0xbfc00a07 a1: 0xb1100000 a2: 0x00000000 a3: 0x80594eff
R8: t0: 0x00000040 t1: 0x00000020 t2: 0x80594ef7 t3: 0x805916f8
R12: t4: 0x00000000 t5: 0x0000000d t6: 0x47e3a63c t7: 0x4c75a632
R16: s0: 0x00000002 s1: 0xbf9e5b5f s2: 0xffd3ffd8 s3: 0xfffaf346
R20: s4: 0xf3aafd8f s5: 0xb3efbd59 s6: 0xd774ddcf s7: 0xdfff31df
R24: t8: 0x00000001 t9: 0x805916d8 k0: 0x00000000 k1: 0x00000000
R28: gp: 0x80598630 sp: 0x8047fff0 fp: 0x5fffaf49 ra: 0xbfc00a28
[/CODE]
I know 5210G is now end of life, but I dont want to part with my sleek CPE yet.
Any hopes of reviving this ? or its a dump now ?
my brick is deeper i think
Hola señor Victor
Gracias por su respuesta. Estaba siguiendo tu post.
Hay un problema en mi caso. No estoy consiguiendo comienzo del bootloader.
Sólo romstart falló cada 10 segundos ..
Intenté entrar TPL, pero no sucedió nada. ¿Es si completamente bricked?
Hello Victor
Thanks for you reply. I was following your post .
There is one problem in my case.
I am not getting bootloader start. just romstart failed every 10 seconds..
I tried entering TPL , but nothing happened. Is if fully bricked ?