T1600G 28ps intervlan problem
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi,
Would like to ask the T1600G -28 PS would support inter-vlan function ? Detail as follows:
One no of T1600G - 28PS
Two PC, PC1 and PC2
Set Vlan A port, 1/0/1 to 8 with untag mode
Set Vlan B port, 1/0/9 to 16 with untag mode
PC 1 connect in Vlan A and IP address is 192.168.10.10 255.255.255.0
PC 2 connect in Vlan B and IP address is 192.168.20.20 255.255.255.0
I have already Set SVI IP address on VLAN A : 192.168.10.1 255.255.255.0 and VLAN B : 192.168.20.1 255.255.255.0 and no static route added.
But I still can't ping each other. Anything I am doing wrong ?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Dear @JACKFOK,
If you ping the gateway on the PC, do you get replies successfully? How about ping the other PC in the same VLAN?
If ping doesn't work, you may check the firewall settings on your PCs and ensure the ping request is not blocked.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Dear Fae,
Thanks for the help. Your informations is very useful.
Just asking if I decide the network will not need to access Internet, can the T1600 G switch will do the inter-vlan routing by itself only without the help of router ? Thanks.
Jack
- Copy Link
- Report Inappropriate Content
Dear @JACKFOK ,
Just asking if I decide the network will not need to access Internet, can the T1600 G switch will do the inter-vlan routing by itself only without the help of router ? Thanks.
I believe yes. The T1600G-28PS V3 supports L3 Features-Interface, which is for inter-vlan routing.
- Copy Link
- Report Inappropriate Content
Dear Fae,
Once again thank you for your help. If I refer to this FAQ, and I have the same three nos. of VLAN and L3 interface setting on my T1600G switch. What about the IPv4 static route setting in the L3 features page? Is it set to 192.168.0.126 as the default VLAN 1 ? Then I can ping it within different VLAN and have response. Thanks.
Regards,
Jack
- Copy Link
- Report Inappropriate Content
Dear @JACKFOK,
Once again thank you for your help. If I refer to this FAQ, and I have the same three nos. of VLAN and L3 interface setting on my T1600G switch. What about the IPv4 static route setting in the L3 features page? Is it set to 192.168.0.126 as the default VLAN 1 ? Then I can ping it within different VLAN and have response. Thanks.
In the FAQ you read, the static routing is to make all traffic forward to the uplink gateway, thus the devices in different VLANs can talk to the same gateway. If you just want devices can communicate among different VLANs within the switch, no need to configure IPv4 static routing.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi
After set up the interface ip address in the L3 page and the VLAN conf. in the L2 page. the two PCs which have 2 different VLAN still can't ping each other. And the PVID is set. Detail as below
interface vlan 100
set ip address 192.168.10.1 255.255.255.0
interface vlan 200
ip address 192.168.200.1 255.255.255.0
interface gigabitEthernet 1/0/1
switchport general allowed vlan 100 untagged
switchport pvid 100
interface gigabitEthernet 1/0/2
switchport general allowed vlan 200 untagged
switchport pvid 200
Connect a PC to port 1, set IP address 192.168.100.2/24 for it. Gateway is 192.168.100.1.
Connect a PC to port 2, set IP address 192.168.200.2/24 for it. Gateway is 192.168.200.1.
And no ping happen.
Thanks.
Jack
- Copy Link
- Report Inappropriate Content
Dear @JACKFOK,
If you ping the gateway on the PC, do you get replies successfully? How about ping the other PC in the same VLAN?
If ping doesn't work, you may check the firewall settings on your PCs and ensure the ping request is not blocked.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@JACKFOK ,
After fire wall setting off. All PC can ping each other. Thanks a lot.
Thank you for coming back and sharing the results. Glad to know that your concern was resolved finally.
Hope you enjoy the internet with the TP-Link products. Cheers!
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1958
Replies: 10
Voters 0
No one has voted for it yet.