SOHO Switches
Knowledge BaseTP-Link Switch Naming Format
Background: This guide aims to provide insight into our TP-Link switch naming format. This Article Applies to: All TP-Link switches. Naming and Differences: TP-Link switch is a series of Easy Smart an
Official
2Helpful
11060Views
Knowledge BaseCommon Questions About 802.1Q VLAN
The topic was originally posted by Clive_A in Common Questions About 802.1Q VLAN Background: We hope this article can be helpful in your understanding of 802.1Q VLAN. This Article Applies to: All Omad
By
Clive_A
Clive_A1Helpful
9198Views
Configuration GuideHow to Configure VLAN on TP-Link Switch
The topic was originally posted by Clive_A in How to Configure VLAN on TP-Link Switch Background: This post provides a configuration guide to set up a VLAN-tagged and untagged port, PVID, and trunk on
By
Clive_A
Clive_A1Helpful
10202Views
The topic was originally posted by Clive_A in Howto - A Guide to Use Forum Effectively. Read Before You Post. Hi, if you are new to the forum, we would love to show your how to use our forum and make
By
Clive_A
Clive_A0Helpful
6309Views
The topic was originally posted by Clive_A in Common Questions About the Hardware Version and Firmware Update Background: We aim to demystify the distinctions among our hardware versions and address a
By
Clive_A
Clive_A1Helpful
7211Views
I have two of the TP-Link TL-SG108S-M2 connected over CAT 6 Ethernet (approx 60-80 feet) and have various 100 Mbps, 1Gbps, and 2.5Gbps devices connected on both switches. On one switch the 2.5Gbps dev
0Helpful
45Views
Hello. I have the exact same problem as described in https://community.tp-link.com/en/home/forum/topic/673210 The management interface becomes unavailable from a trunked port after approximately 4-5 m
By
JoshControl
· Latest post a week ago
by JoshControl
0Helpful
1030Views
Hi everyone, I’m currently using a TP-Link TL-SG1218MPE 18-Port Gigabit Easy Smart PoE+ switch in my rack, and it has been working well for my setup. However, the internal fans are noticeably loud, an
PoE
5Helpful
8354Views
I just bought an TL-SG105PE but I cannot get it to obtain an IP address and thus I cannot access the configuration interface. This seems to be due to a faulty implementation of the DHCP protocol. Upon
Network ConnectivityConfigurationFirmware UpdateDHCP
1Helpful
276Views
We use the TP-Link SG1024DE in our networks and have identified a bug in the newer versions of the switch. When a IGMPv2 membership query is sent over the switch, if a IGMPv2 membership report is then
VLAN & Multi-NetworksNetwork ConnectivityIGMPv2
By
Peter_Immt
· Latest post 2026-03-12 03:46:04
by Hank21
0Helpful
318Views
Hello, I just bought the TL-SG105E V5 switch, which came with installed firmware version "TL-SG105E(UN) V5_1.0.0 Build 20220414". I installed the Easy Smart Configuration Utility and I tried to update
By
Chris_de_Ze
· Latest post 2026-02-25 07:29:33
by Hank21
0Helpful
158Views
Bottom Line Up Front - newer versions of the SG108E will implement VLANs properly. My v2 would not but my v5 works as expected. Details: VLANs settings on version 2 of my SG108E did not segregate broa
Firmware UpdateVLAN & Multi-NetworksConfiguration
0Helpful
406Views