Switches
Hello, I would like to validate whether the following network design and security model is technically feasible using TP-Link Omada, specifically with inter-VLAN ACLs and granular exceptions (IP + por
VLAN & Multi-NetworksACLStatic RoutingConfiguration
0Helpful
294Views
I am trying to get a WAS-110/X-ONU SFP+ working on a SG3428X-M2 switch. This is to replace my ISP (Virgin Media HUB5x) router - 192.168.0.1. I have a ER7212PC - 192.168.0.11 controller plugged in to t
VLAN & Multi-NetworksConfigurationNetwork ConnectivityStatic Routing
0Helpful
878Views
Hi! I'm new to tp-link and i've got a good first impression especially in price per performance. I got a new setup with some vlans and the switch is acting as cross-vlan gateway/router and its working
ConfigurationVLAN & Multi-NetworksACLStatic Routing
By
name_not_found
· Latest post 2025-12-10 15:30:26
by name_not_found
0Helpful
376Views
Hello, good morning dear community! I've been having a problem that I haven't been able to solve for a couple of days now. I need to create three VLANs within an SG3428XMP switch, and two of them need
VLAN & Multi-NetworksStatic RoutingNetwork ConnectivityConfiguration
0Helpful
350Views
Hi! I kindly ask for your advice as I don't find any help with getting omada to configure static routes between clients. I do have an opnsense-firewall that is my gateway (default and vlans) and acts
ConfigurationStatic Routing
0Helpful
420Views
I'm having trouble setting up my switch and getting it to connect to my software controller. My network is at 10.6.1.0/24 but the switch turns on with the IP 192.168.0.1 I was very surprised because t
DHCP ServiceStatic RoutingControllerNetwork Connectivity
By
JumpingPeach
· Latest post 2025-10-01 12:07:59
by JumpingPeach
1Helpful
1309Views
using TP-Link SG2210P switches as access switches (L2) managed by Omada Controller. SG3428 is functioning as DHCP and Routing. Network works fine initially. Routing stops temporarily, but starts worki
Static RoutingDHCP ServiceController
1Helpful
282Views
Hi All, I followed instructions from below link: https://www.tp-link.com/pl/support/faq/4017/ Basically I wanted to achieve very same network schema, the only difference is that my Internet Gateway is
DHCP ServiceStatic RoutingConfigurationVLAN & Multi-Networks
By
MarekZegarek
· Latest post 2025-04-24 13:52:33
by GRL
2Helpful
1851Views
I trying to set up a VLAN network(192.168.10.1) separate from the main network(192.168.1.1). I was able to configure ports and enable DHCP for VLAN 10. I also want to enable inter-1 VLAN routing. NOTE
VLAN & Multi-NetworksStatic RoutingDHCP Service
1Helpful
1386Views
I have connected the switches as follows: SX3016F: Port 1 = PVID 11 (untagged) & Port 28 = Tagged SG3428XMP: Default settings (PVID 1, Tagged: VLAN 11 & VLAN 28) Currently, when I connect a device to
VLAN & Multi-NetworksConfigurationNetwork ConnectivityStatic Routing
1Helpful
729Views
Hi all, I'm newcomer in network community and I have a problem with my local subnet and router. I can't provide internet from router into my switch. I tried provide internet to switch by using static
ConfigurationStatic RoutingVLAN & Multi-Networks
0Helpful
615Views
Hi, I was looking through multiple post but couldn't find the right answer for my issue. This is my first router with VLAN and I have the following scenario: I want to setup multiple VLANs for differn
VLAN & Multi-NetworksConfigurationStatic Routing
4Helpful
2015Views