Gateways
[Bug] ER707-M2 v1.20 FW 1.4.1: dhcp6s opens 2x UDP sockets on :547, only reads from one, other grows
Summary When SLAAC+Stateless DHCP is enabled on a LAN interface, the dhcp6s process (PID 12669) opens two UDP sockets bound to :::547. Only one socket is actively serviced. The other accumulates unrea
DHCP ServiceIPv6
1Helpful
142Views
The configuration of IPv6 on the Omada gateway is pitiful. There is no 6in4 tunneling available, there is no comprehensive method for configuring IPv6 for usage in the controller. There is minimal con
IPv6ControllerACL
0Helpful
221Views
I've read a handful of threads about the IPv6 "firewall" (likely misreferenced as an ACL). I saw from searching the forums in a somewhat recent thread from 2025 there is a "deny all by default" ACL fo
IPv6FirewallACL
By
therealbob
· Latest post 2026-02-14 02:37:42
by Hank21
0Helpful
369Views
How can configure Omada router TL-ER7206 ipv6 on multiple vlans with ipv6-pd length 56. Currently I can enable ipv6 only on one vlan. My ISP is Rogers Cable in Canada that provides ipv6 prefix delegat
WAN SetupVLAN & Multi-NetworksIPv6
By
mma678
· Latest post 2026-02-10 20:36:43
by Julian2111
0Helpful
497Views
Hello. I have updated firmware within the last three weeks and I am trying to enable IPV6. After a lot of searching I have seen screengrabs (including from on here) which show a simple line under "gen
IPv6
0Helpful
689Views
I'm only able to get a /64 IPv6 prefix from my ISP. They suggested trying: Sending a prefix hint with a requested prefix - omada controller does not support this, standalone gateway does not support t
IPv6
By
DcnPat
· Latest post 2026-01-07 01:38:03
by Vincent-TP
0Helpful
357Views
I am working on getting an IPV6 address from my ISP on my Omada Gateway. I have tried a variety of settings, but am unable to get any address. My ISP provided an NH20A NAH that I have placed into brid
WAN SetupIPv6
By
ProtoTempus
· Latest post 2025-11-11 23:32:41
by ProtoTempus
1Helpful
822Views
Hello, here is another problem I am currently experiencing. I activated IPv6 support because of a new Internet Provider (CGNAT). So I activated IPv6 for the WAN connection, stored the prefix delegatio
WAN SetupACLFirewallIPv6
0Helpful
714Views
Hi. I configured the WAN settings for a new ISP. Due to CGNAT, I had to activate IPv6. The connection was established successfully. However, the router status now shows a local link address for IPv6.
WAN SetupIPv6
0Helpful
462Views
Hello everybody, I trry to setup a VLAN with DHCPv6 with prefix delegation. There is a Fritz!Box router connected to the ER605 witch needs this kind of setup to provide IPv6 addresses to its clients.
WAN SetupIPv6VLAN & Multi-Networks
0Helpful
696Views
I am currently using the TP-Link ER605 v2.0 router in combination with the Omada Controller, connected directly to KPN-NL fiber. KPN provides both IPv4 and IPv6 connectivity, and I would like to ensur
WAN SetupIPv6IPTVKPN
By
cmcouwenb
· Latest post 2025-09-16 01:39:24
by Vincent-TP
1Helpful
1441Views
Been trying to get IPv6 working for a few days on the ER8411, but it seems to have an issue routing anything to the WAN interface. To preface this, I know IPv6 is working from my ISP side as I can get
WAN SetupIPv6
2Helpful
1428Views