How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 01:29:35
Hardware Version: V3
Firmware Version:

Hi, 

So we have 1 Managed switch to Bldg. B, and an Unifi UAP-AC-PRO setup with VLAN30 and VLAN40 option.

Our Local LAN is 10.10.6.x 

VLAN 30 is 192.168.30.x

VLAN 40 is 192.168.40.x

 

 

We do have 2 internet connection 

Default Gateway 1 is 10.10.6.10

Default Gateway 2 is 10.10.6.9

We added the 2 default gateways  and set an IP of 10.10.6.245 for the Managed Switch.

 

I can ping the Access Point but no internet

Maybe adding the VLAN30 and VLAN40 to the Port where the Access Point was plugged can solve the problem.. but can you add 2VLAN in a Port?

Any tips on setting this up? Thank you

 

  0      
  0      
#1
Options
19 Reply
Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 01:59:02

Hi mariem56

 

If the packets sent from Unifi UAP-AC-PRO has vlan tag, as you said, you need to add VLAN30 and VLAN40 to the Port where the Access Point was plugged. You need to change the port to general port then you can add two VLANs in a port. I think most TP-Link switch is using general port.

And you still need to add VLAN30 and VLAN40 to the Port connected to the gateway, otherwise, the packets from AP cannot reach gateway. 

 

About the network related to multiple subnets, I think you still need to configure other feature like VLAN interface, static routing and so on. Please see the following FAQ.

https://www.tp-link.com/en/support/faq/887/

  2  
  2  
#2
Options
Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 06:52:37

Does your switch connect directly to gateway or are there any other managable switches? If directly, then as Andone said, configure uplink port (port which goes to gateway) as vlan 30/40 tagged. If you have more switches, then you need keep trunk port (30/40 tagged) till the gateway. 

What is your gateway? It should also support vlan30/40 tagged on port, where you connect switch.

  0  
  0  
#3
Options
Re:Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 06:57:16
So its possible to add 2VLAN on an same Port?
  0  
  0  
#4
Options
Re:Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 07:00:23 - last edited 2019-06-06 07:00:58

I remember that I add 10.10.6.9 and 10.10.6.10 which two of our  gateways that I have.. so I can add the VLAN30 and VLAN 40 to the Uplink port too? BTW my main router is pfSense... Thanks for the response

  0  
  0  
#5
Options
Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 07:06:14

You didn't provide your firmware. It's important, because old firmwares had one design (with access/general/trunk port modes), while new firmwares have only general port mode (which is OK also, but could be different to configure.)

 

Of course, you can configure several VLAN's on port. You can conifgure even all VLAN's on port (switchport general allowed vlan 1-4094 tagged), it is not a big deal for normal managed switch. The only point is just you need to understand the difference between tagged port and untagged. It's a basic topology, when you configure 20 ports each with your own vlan untagged, then you have uplink port, which have all your 20 VLANs tagged to transfer it further on your topology.

 

Switchport general allowed vlan 30,40 tagged - it is how you add 2 VLANs, as example. Your Ubiquiti VLAN 30, VLAN 40 means it has tagged port from AP, so you need also tagged port on switch. Cheers.

  1  
  1  
#6
Options
Re:Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 07:21:01
Thank you for your reply.. I'm actually can't fully understand VLAN.. firmware i think it V3_181101... so my 10.10.6.x will be my LAN and VLAN 1 which configure to all port as default right? Then I'll add VLAN30 and VLAN40 to for example port 16 which then make the Port 16 my VLAN1 , VLAN30 and VLAN40? I wish I can watch tutorial specifically for add VLANs on a single port...
  0  
  0  
#7
Options
Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 07:33:00

I'm using CLI, so I gave command above. It is not so comfy to do it by Web-interface, but here it is https://www.tp-link.com/en/support/faq/2149/ 

Can I draw your topology? Why do you need 2 gateways? Who is DHCP-server for the network? I hope you understand, that host can have only 1 gateway the same time. I can only understand 2 gateways, if you configure VRRP between them of smth like this.

So, as I understand If you have only 2 SSID's with vlan 30,40 and vlan 1 is for managing AP (and seems like not only AP), right? Also you have 1 subnetwork for the whole LAN. Then you need switchport general allowed vlan 1 untagged, switchport pvid 1, switchport general allowed vlan 30,40 tagged.

Your uplink, which goes to router also should be the same. Your pfsense router (sorry, I have never used it), should be configured also the same, VLAN 30,40 tagged, vlan 1 untagged, PVID 1. That is how I would configure it on any Miktotik or TL-ER6120 and it would work :)

 

P.S. I quickly looked thorugh pfsense configuration and it seems complicated, as it is some kind of enterprise solution as cisco, where you need configure even NAT and all the stuff.

 

  1  
  1  
#8
Options
Re:Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-06 08:54:43
We actually have two internet connections for failover but not group.. meaning its not automatically goes to another connection if the other stopped working.. 2 pfSense box too... We actually need to change the defaultgateway of the user incase the current connection stopped. Were still undecided if we want to automatically do fail over and use only 1 pfSense box... Our 10.10.6.x LAN connection were configured for static and for VLAN the DHCP server is the pfSense.. We were told that the standard should be DHCP then do a per MAC lease...
  0  
  0  
#9
Options
Re:Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-07 04:39:18

This is what I've tested

 

I create another VLANs aside from default VLAN 1

created VLAN 30 (192.168.30.0/24) and VLAN 40 (192.168.40.0/24)  both are untagged ports to Ports 1, 15, 16.

Then adding PVID but its per port so I only added port 1,15,16 with PVID 30.

 

Then going to L3Features >IPV4 Routing Table:

 

Protocol        Destination Network                        Next Hop               Distance             Metric               Interface Name

Static                0.0.0.0/24                               10.10.6.10                        1                       0                            VLAN1

Connected       10.10.6.0/24                            10.10.6.247                      0                       1                             VLAN1

Connected       192.168.30.0/24                    192.168.30.1                      0                       1                             VLAN30

Connected       192.168.40.0/24                     192.168.40.1                     0                        1                            VLAN40

 

then L3Features  > Interface

          VLAN 40                     Static            192.168.40.1              255.255.255.0          VLAN40_Guest       Up         

          VLAN 30                     Static            192.168.30.1              255.255.255.0          VLAN40_Guest       Up          

          VLAN 1                       Static            10.10.6.247                255.255.255.0          LAN Trusted            Up

 

 

10.10.6.247 IP of Managed Switch

 

I can ping the Switch, the Access Point 

but I still dont have internet on my access point

When I physically connect my Laptop to Managed switch I can ping users that's directly connected to Switch..

 

What could be the problem?

  0  
  0  
#10
Options
Re:Re:Re:How to add 2 VLAN to a port TP-Link 26000G 52-TS 48Port Switch
2019-06-07 05:33:15

Answer:

Instead of untagged the VLAN 1(Port 1-52) , VLAN 30(Port 16), VLAN 40(Port16) 

we tried tagged VLAN 30 (Port 1 and Port 16), VLAN 40 (Port 1 and Port 16) and it worked! I can now connect to my Access Point with VLAN 30 and VLAN 40..  

  1  
  1  
#11
Options

Information

Helpful: 0

Views: 4616

Replies: 19