TL-Er6120 dynamic IP and one-to-one nat support

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-Er6120 dynamic IP and one-to-one nat support

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-Er6120 dynamic IP and one-to-one nat support
TL-Er6120 dynamic IP and one-to-one nat support
2020-08-10 03:29:23 - last edited 2021-04-18 11:04:49
Model: TL-ER6120  
Hardware Version: V3
Firmware Version: 3.0.1

When using dynamic IP from the ISP, the router is unable to use One to One NAT for an ip address block, as disclosed in the user manual

 

Is there any way to bypass this or plans for this to be a supported feature?

 

 

  0      
  0      
#1
Options
1 Accepted Solution
Re:TL-Er6120 dynamic IP and one-to-one nat support-Solution
2020-08-12 03:26:37 - last edited 2021-04-18 11:04:49

Hello @Daniel2348 

 

I'm currently looking to use a Dynamic-only framed route from our ISP to host several webservers (port 80/443) by assigning the ips to specifc servers

Is there a similar router/firewall combo that would allow Dynamic WAN connections and one to one routing?

 

The One-to-One function on the TP-Link router would require static IP addresses provided by ISP. I'm afraid that none TP-Link products can meet your demands at present.

 

Best regards.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:TL-Er6120 dynamic IP and one-to-one nat support
2020-08-10 11:12:24 - last edited 2021-04-18 11:04:49

Dear Daniel2348,

 

We are afraid that One-to-One NAT only takes effect when the WAN connection type is Static IP.

 

May I check your network requirements in detail?

 

If your purpose is to have some specific external IPs to access the internal server behind the router, Virtual Server with Access Control can make it. The instruction below is for your reference. 

https://www.tp-link.com/support/faq/2026/

 

Best Regards.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:TL-Er6120 dynamic IP and one-to-one nat support
2020-08-11 10:19:18 - last edited 2021-04-18 11:04:49

Thanks for your response@Fae 

 

Unforunately that won't work for our use case

 

I'm currently looking to use a Dynamic-only framed route from our ISP to host several webservers (port 80/443) by assigning the ips to specifc servers

 

Is there a similar router/firewall combo that would allow Dynamic WAN connections and one to one routing?

 

 

  0  
  0  
#3
Options
Re:TL-Er6120 dynamic IP and one-to-one nat support-Solution
2020-08-12 03:26:37 - last edited 2021-04-18 11:04:49

Hello @Daniel2348 

 

I'm currently looking to use a Dynamic-only framed route from our ISP to host several webservers (port 80/443) by assigning the ips to specifc servers

Is there a similar router/firewall combo that would allow Dynamic WAN connections and one to one routing?

 

The One-to-One function on the TP-Link router would require static IP addresses provided by ISP. I'm afraid that none TP-Link products can meet your demands at present.

 

Best regards.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 609

Replies: 3