Business Community > Controllers > Omada OC200 connection type constant switching
< Controllers

Omada OC200 connection type constant switching

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Omada OC200 connection type constant switching

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Omada OC200 connection type constant switching
Omada OC200 connection type constant switching
2021-01-01 10:19:30 - last edited 2021-03-25 02:18:21
Model: OC200  
Hardware Version: V1
Firmware Version: 1.7.3 Build 20201119 Rel.63433

Hello,

last week I updated the firmware on the OC200. Yesterday I found out that wifi clients are incorrectly detected. They randomly switch WiFi clients from Wifi to LAN.

All network devices has updated, no have VLANs. 

 

My network contains:

Omada OC200 controller version 4.2.8, fw 1.7.3 Build 20201119 Rel.63433

TL-R605 router V1          fw 1.0.0 Build 20200930 Rel.36519

TL-SG108E switch          fw 1.0.0 Build 20181120 Rel.40749

1x EAP245 V3                fw 5.0.0 Build 20200918 Rel. 61625
1x EAP 225 outdoor V1  fw 5.0.0 Build 20200918 Rel. 58628

 

I tryed:

- Omada OC200 reset and restore older cfg

- readopting all devices

How do I fix this?

 

Thank you very much,

Pavel

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Omada OC200 connection type constant switching -Solution
2021-03-25 02:17:47 - last edited 2021-03-25 02:18:21

Hi All,

 

As an update, the "Wireless Clients showing as Wired in SDN" problem has been fixed in the Omada SDN Controller v4.2.11 already.


If you have any further issues/concerns, please feel free to start a new thread on the community.

BTW, the thread below will be updated once there is new firmware released in the future, welcome to subscribe to it.
【Update 3/4/2021】Latest firmware released for Omada SDN Controller v4.2.11

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#21
Options
16 Reply
Re:Omada OC200 connection type constant switching
2021-01-01 13:47:02 - last edited 2021-01-04 05:44:25

@PavelV 

After reboot both AP topology is ok:

but in a moment it is wrong again:

  0  
  0  
#2
Options
Re:Omada OC200 connection type constant switching
2021-01-01 14:01:00 - last edited 2021-01-04 05:44:25

@PavelV 

I may have to replace the older switch with this omada supported TL-SG2008P

  0  
  0  
#3
Options
Re:Omada OC200 connection type constant switching
2021-01-05 17:13:54

@PavelV 

next screen, it's really not okay

  0  
  0  
#4
Options
Re:Omada OC200 connection type constant switching
2021-01-05 19:45:38 - last edited 2021-01-05 19:54:25

@PavelV I have same problem after upgrade. Switching from AP to LAN after 5 minutes. I dont know why :(. I have three networks with OC200. But i have this error only in network with TL-R605 router

  0  
  0  
#5
Options
Re:Omada OC200 connection type constant switching
2021-01-05 19:46:37

@PavelV 

  0  
  0  
#6
Options
Re:Omada OC200 connection type constant switching
2021-01-06 19:21:52

@Zdenek 

Hi Zdeňku, where is it possible to get this log?

  0  
  0  
#8
Options
Re:Omada OC200 connection type constant switching
2021-01-06 19:55:59

@PavelV hi. It's in Log/Event

  0  
  0  
#9
Options
Re:Omada OC200 connection type constant switching
2021-01-06 21:30:01

@Zdenek

Thank you, in my log is "logged in to the controller" and once "EAP245_1.patro was readopted automatically, EAP225_zahrada was readopted automatically, TP Link TL-R605 was readopted automatically.

  0  
  0  
#10
Options
Re:Omada OC200 connection type constant switching
2021-01-06 22:58:42 - last edited 2021-01-06 23:29:20

@PavelV 

 

I have the same problem, without the Omada OC200.

 

Wifi clients are registered as a wired clients.

 

 

Setup location Ship(little cruise): OC200 (2.9.3 Build 20230328 Rel.52390) 1X EAP110 3x EAP245(EU) v3.0 11x EAP245(EU) v4.0
  0  
  0  
#11
Options
Re:Omada OC200 connection type constant switching
2021-01-09 08:53:54

@Lowie 

Hello,

I compared your Omada_Controller_V4.2.8_Windows, in my Omada OC200 is the same version.
It may contain an error.

  0  
  0  
#13
Options
12

Information

Helpful: 0

Views: 4497

Replies: 16

Related Articles
Switching Between OC200 & Omada Software Controller
742 0
omada oc200 version 5.14.26.23 voucher type no portal display and always loading portal
435 0
issue in omada oc200
501 0
OC200 Connection timed out
1233 0
Omada OC200 voucher hotspot
941 0
Omada OC200 and TL-R605
2002 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.