lan wan balance router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

lan wan balance router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
lan wan balance router
lan wan balance router
2021-01-15 10:01:04 - last edited 2021-04-18 09:56:41

Hello, thanks to anyone help me and I hope to explane as well what I need, sorry for my english.
Dubts on ip addresses.

I have two internet connections Router WAN1 ip 192.168.1.1 and Router WAN2 192.168.1.2 (in this I cannot change ip address).
Router WAN1 is the default gateway on all my pcs (all pcs have static ip), so Router WAN2 is not used.
I think to buy TL-R470T+ Balance router (then I call it ROUTER) and use both WAN1 and WAN2.

Questions:

1. can I use for ROUTER 192.168.1.3 ip? (then I'll change on all my pcs default gateway from 192.168.1.1 to 192.168.1.3)?
2. if not possible question #1, if I set ip ROUTER 192.168.0.3,  can I set default gateway ip 192.168.0.3 on my pc with ip 192.168.1.4? Does that pc use internet then?
 

  0      
  0      
#1
Options
3 Reply
Re:lan wan balance router
2021-01-16 02:17:36 - last edited 2021-04-18 09:56:41

@mobile75 

 

Hey

 

Think I follow you ok

 

If you are asking, personally I would keep the new ROUTER on a separate range.   Something like 192.168.10.1    Then just allow it to route the data to WAN 1 and WAN 2 as required.  Separate your LAN from your WAN

 

Your clients would then get DHCP addresses in the range 192.168.10.x  with default gateway of  192.168.10.1   The TL-R470T  can then route the traffic to WAN1 and WAN2 on a separate network.

 

That is how i have my TL-R605 setup

 

  0  
  0  
#2
Options
Re:lan wan balance router
2021-01-25 09:10:50 - last edited 2021-04-18 09:56:41

I have solved, but now I need other help.

 

Can anyone help me to learn how to do these 2 settings?

 

1. if some clients try to use UPD or TCP port 5060 I need to use WAN2

 

2. if some clients try to connect to (example external ip address) 123.123.123.123 ip address I need to use WAN2

 

Thanks in advance.

  0  
  0  
#3
Options
Re:lan wan balance router
2021-01-25 10:39:37 - last edited 2021-04-18 09:56:41

@mobile75 

 

Hey again

 

Hopefully this will help

 

if some clients try to use UPD or TCP port 5060 I need to use WAN2

 

You need to go to preferences > service type and create a new service for the ports you need (see below)

 

 

 

You can then go to TRANSMISSION > ROUTING > POLICY ROUTING and create a profile to move the new service you created above.. to the WAN2 Port.   Again example below.

 

 

----------------

if some clients try to connect to (example external ip address) 123.123.123.123 ip address I need to use WAN2

 

Try setting a static route for the IP via WAN2, example below

 

 

 

The next hop would likely be the router address, however I have not tested this.. you may need to play around to get this working

 

 

 

 

 

 

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 435

Replies: 3

Related Articles