How to enable Test Mode in CPE710(UN) ver1.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to enable Test Mode in CPE710(UN) ver1.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to enable Test Mode in CPE710(UN) ver1.0
How to enable Test Mode in CPE710(UN) ver1.0
2021-02-05 09:51:35 - last edited 2021-02-08 09:01:30
Model: CPE710  
Hardware Version: V1
Firmware Version: 2.2.0 Build 20200304 Rel. 70345 (5553)

Hi, Recently bought this CPE. However, I can't see all available 5Ghz networks in my area. It can't even find my own homes 5ghz network. It can only find channels above 5700+. I read somewhere that I could select test mode as region to have all channels be available to me. But I cant find it anywhere, not even  when I reset the Modem. I upgraded the firmware to the latest one earlier only to downgrade it later on as is was a US version. So I stick with the UN firmware version as I didnt know this is where the test mode is available only. But no matter how much I factory reset it, it won't show me the option to select Test Mode in the region. Theres no region option in the settings, what do I do to enable test mode?, or at least allow me to view all 5ghz networks in my area really?.

PS: I Tried downgrading to the original firmware I had when I bought it which is 

2.2.0 Build 20200304 Rel. 70345 , but still, there is no option to enter test mode or any option to change the region. I could only basically connect to 5ghz networks that has a frequency above 5700mhz

FYI. Turns out another person had the same exact issue as I had at this thread. Can anyone help me have the option to select country/region back?
  0      
  0      
#1
Options
1 Accepted Solution
Re:How to enable Test Mode in CPE710(UN) ver1.0-Solution
2021-02-07 03:32:53 - last edited 2021-02-08 09:01:30

Dear @iamjoshua,

 

Solution provided HERE.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  3  
  3  
#2
Options
6 Reply
Re:How to enable Test Mode in CPE710(UN) ver1.0-Solution
2021-02-07 03:32:53 - last edited 2021-02-08 09:01:30

Dear @iamjoshua,

 

Solution provided HERE.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  3  
  3  
#2
Options
Re:How to enable Test Mode in CPE710(UN) ver1.0
2021-02-07 08:07:06

 

Fae wrote

Dear @iamjoshua,

 

Solution provided HERE.

@Fae Hi thanks, I already sent an email for support as suggested in that thread. Waiting for an immediate reply as I need the antenna to work already. Thanks.

  0  
  0  
#3
Options
Re:How to enable Test Mode in CPE710(UN) ver1.0
2021-05-26 07:55:07

@iamjoshua 

has your problem been resolved?
  0  
  0  
#4
Options
Re:How to enable Test Mode in CPE710(UN) ver1.0
2021-05-26 11:02:11

@Aqit 

Aqit wrote

@iamjoshua 

has your problem been resolved?

yes, contact their support so that their tech support could flash your firmware to the correct firmware version.

  0  
  0  
#5
Options
Re:How to enable Test Mode in CPE710(UN) ver1.0
2021-11-07 03:09:57

@iamjoshua 

Hi,i have the same problem because I don't have the region option so I can choose the test mode.Could you please send me a UN firmware version from the tp-link manufacturer.Thank you!

  0  
  0  
#6
Options
Re:How to enable Test Mode in CPE710(UN) ver1.0
2022-01-14 15:26:37

@Fae hi fae it s possible you can help me to change my cpe 710 (US) firmware (2.2.1 Build 20201208 Rel. 38063 (5553)

to an UN firmare..

 

thanks in advance

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 2749

Replies: 6

Related Articles