OC 200 firmware update 1.7.4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

OC 200 firmware update 1.7.4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
OC 200 firmware update 1.7.4
OC 200 firmware update 1.7.4
2021-03-05 02:59:24
Model: OC200  
Hardware Version: V1
Firmware Version: 1.7.4

Just updated to the latest OC200 a few minutes ago.

 

now it is stuck in this infinite loop of trying to adopt/ provision the R605 router.

 

anyone else run into this ? 

  0      
  0      
#1
Options
19 Reply
Re:OC 200 firmware update 1.7.4
2021-03-05 06:39:53

@Rickk10000 sorry i do upgrade but not using any tplink router, for me is a different story it crashes my main oc200 v1 controller after the upgrade. while in my the backup controller running smoothly so far. I will try the recovery mode for my main controller today :) hopefully, it's not totally brick.

  0  
  0  
#2
Options
Re:OC 200 firmware update 1.7.4
2021-03-05 10:59:21

@Rickk10000 

 

Hello,

which fw versione has TL-R605?
try to power off and then power on.

 

Best Regards

  0  
  0  
#3
Options
Re:OC 200 firmware update 1.7.4
2021-03-05 11:59:36
Thank You but I'm not using TL-R605 in my configuration and setup/.
  0  
  0  
#4
Options
Re:OC 200 firmware update 1.7.4
2021-03-05 16:29:56

I havde the same problem, a OC200 with 1.7.4 and a R605 router, now I have a OC200 brick, 
reset many times, tried power over POE and USB, tried  both lan ports and nothing, 
TP-Link writes lifetime warrenty on the OC200 box, let's see what that gets me.

  0  
  0  
#5
Options
Re:OC 200 firmware update 1.7.4
2021-03-05 18:35:37 - last edited 2021-03-05 18:37:17

@Rickk10000 

 

Was the the update pulled back?  I downloaded it the other day, but I went to dowload it again on a different computer and get the following:

 

"Please go to TP-Link Offical Website to get products, software and services for your region.

Visit official TP-Link website >"

 

When I go there 1.7.4 isn't listed.

 

I was planning to update the TL-R605 today, haven't added it to my system yet, but it looks like there might be problems, so I might wait..

  0  
  0  
#6
Options
Re:OC 200 firmware update 1.7.4
2021-03-05 20:10:55

Ran the update on OC200 and same issue. R605 is stuck in provisioning state. Granted I did not push the latest update to the R605 , and now that makes me wonder if there was something in the router's update that allowed for provisioning to the OC200 after the OC200 firmware was updated.

 

 

@Fae  any help on this issue?

 

The R605 is still connected via the internet but no longer able to administrate the device with the Omada Controller

  0  
  0  
#7
Options
Re:OC 200 firmware update 1.7.4
2021-03-05 20:17:24

@Reconboy 

 

I remember I had the same issue when upgraded from 4.2.4 to 4.2.8 and resolved with a power off and power on of the gateway.

  0  
  0  
#8
Options
Re:OC 200 firmware update 1.7.4
2021-03-06 02:34:31

Rookie mistake , weird but still a mistake. Did not realize the username and password for the adoption was different. R605 now connects as it should. However, I am seeing the OC200 time out a lot with this latest firmware.

  0  
  0  
#9
Options
Re:OC 200 firmware update 1.7.4
2021-03-06 15:38:23 - last edited 2021-03-06 15:40:15

I got up this morning before anyone else so that I would minimized the whining if anything went wrong.

I rebooted the R605 Router (pulled the power cord)  and the OC200 was then able to talk to it.   I was using my cell phone ap to connect to the OC200. WHen it connected to the router, it told me that there was new firmware available for the router. I let it update the router and now all is fine.

It took the network down for a total of about 10-15 minutes, so be aware of that.

  0  
  0  
#10
Options
Re:OC 200 firmware update 1.7.4
2021-03-06 21:10:47 - last edited 2021-03-06 21:17:55

@Cyclups 

I have the same problem, 
then I wanted to go back to version 1.7.3. but that doesn't work either.

the oc200 no longer works.

 

regarding problem TL-R605, i have also had this bad experience. after an upgrade, the router must always be disconnected from the power supply.

 

 

I am somewhat disappointed by the handling

  0  
  0  
#11
Options