er605 got new firmware "1.1.1 Build 20210723 Rel.64608" but upgrade fails with "wrong file"
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
got notification via oc200 that e new firmware is available, but trying to update from OC200
I obtain error "[MAC address] upgrade failed: The upgrade file is invalid. Please select a correct file."
same error using the .bin file from the support site EN or IT..... [ ER605v1_un_1.1.1_20210723-rel64608_up.bin ]
ps: for completeness upgrade tried from the local network with the local OC200 IP address . purchased from AMAZON EU
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@EZL UPDATE: After a hard restart on er605 (unplug the power source, wait 20 seconds and replug) I tryed again and this time works updating via omada interface on oc200, looks like a adoption bug or something like that.
- Copy Link
- Report Inappropriate Content
Dear @Zephi,
Zephi wrote
Here is the information:
OC200:
Firmware Version :1.8.0 Build 20210406 Rel.58757TL-R605 v1.0:Update firmware 1.1.0 (not the beta) >-- to --> 1.1.1About the time, I tried update via Omada on OC200 and Manual (via bin file in Omada - Custom Upgrade) and both the times takes less than 5 minutes between download (upload in case of manual) and apply.
Thank you for verifying the information. I've reported this upgrade failed issue to the R&D team, who clarifies that the bugs in the older firmware may cause the upgrade to fail and a reboot will fix the issue. So the upgrade will be fine after the reboot, please do not worry about it.
- Copy Link
- Report Inappropriate Content
@EZL Same problem here, even the manual update doesn't work and show the same error.
- Copy Link
- Report Inappropriate Content
@EZL I was able to successfully upgrade, using the software controller however.
- Copy Link
- Report Inappropriate Content
@EZL UPDATE: After a hard restart on er605 (unplug the power source, wait 20 seconds and replug) I tryed again and this time works updating via omada interface on oc200, looks like a adoption bug or something like that.
- Copy Link
- Report Inappropriate Content
@Zephi thanks,
I asked some one on the remote site to unplug and plug the device and after that the update worked.
- Copy Link
- Report Inappropriate Content
Zephi wrote
@EZL UPDATE: After a hard restart on er605 (unplug the power source, wait 20 seconds and replug) I tryed again and this time works updating via omada interface on oc200, looks like a adoption bug or something like that.
May I check the firmware version of your OC200?
Can you recall the previous firmware version of your ER605? Did you upgrade the ER605 firmware from 1.0.1 to 1.1.1?
Kind note that the firmware file will only be kept for 5 minutes. If we haven't started Upgrade within 5 minutes after the firmware (.bin file) is downloaded or uploaded successfully, we may receive the error "The upgrade file is invalid. Please select a correct file".
Perhaps you didn't upgrade it in time after the firmware file is ready?
- Copy Link
- Report Inappropriate Content
Hi @Fae,
Here is the information:
OC200:
- Copy Link
- Report Inappropriate Content
Dear @Zephi,
Zephi wrote
Here is the information:
OC200:
Firmware Version :1.8.0 Build 20210406 Rel.58757TL-R605 v1.0:Update firmware 1.1.0 (not the beta) >-- to --> 1.1.1About the time, I tried update via Omada on OC200 and Manual (via bin file in Omada - Custom Upgrade) and both the times takes less than 5 minutes between download (upload in case of manual) and apply.
Thank you for verifying the information. I've reported this upgrade failed issue to the R&D team, who clarifies that the bugs in the older firmware may cause the upgrade to fail and a reboot will fix the issue. So the upgrade will be fine after the reboot, please do not worry about it.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 3043
Replies: 7
Voters 1
