TL-SG3210XHP-M2 - [Port]/6/Reload port Tw1/0/x phy firmware.
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello,
I'm a new owner of a TL-SG3210XHP-M2 for about a month now, all looked good until today the switch had to be fully powered off and back on, upon powering back up, my sfp+ ports came back on but none of my POE+ ports, that was on FW 1.0.3, tried to unplug/replugged/change ports, force interface up by CLI or GUI... to no avail...Link was always down. All seemed to be working in the last few days, but don't think I tried to fully unplugged the switch and back on, on reboot by CLI or GUI.
My OC200 and AP's are still getting POE+ power but no link on FW 1.0.3.
On FW 1.0.3 after restoring power to the switch
#show interface status
Port Status Speed Duplex FlowCtrl Active-Medium
---- ------ ----- ------ -------- -------------
Tw1/0/1 LinkDown N/A N/A N/A Copper ------> OC200
Tw1/0/2 LinkDown N/A N/A N/A Copper ------> AP1
Tw1/0/3 LinkDown N/A N/A N/A Copper ------> AP2
Tw1/0/4 LinkDown N/A N/A N/A Copper ------> PC for testing
Tw1/0/5 LinkDown N/A N/A N/A Copper
Tw1/0/6 LinkDown N/A N/A N/A Copper
Tw1/0/7 LinkDown N/A N/A N/A Copper
Tw1/0/8 LinkDown N/A N/A N/A Copper
Te1/0/9 LinkUp 10G Full Disable Fiber
Te1/0/10 LinkUp 10G Full Disable Fiber
Only thing that seemed to work was to restore FW 1.0.2, weird?
System Description - JetStream 8-Port 2.5GBASE-T and 2-Port 10GE SFP+ L2+ Managed Switch with 8-Port PoE+
Hardware Version - TL-SG3210XHP-M2 1.0
Software Version - 1.0.2 Build 20210201 Rel.60966
Bootloader Version - TP-LINK BOOTUTIL(v1.0.0)
TL-SG3210XHP-M2#show image-info
Image Info:
Current Startup Image - Exist & OK
Image Name - image1.bin
Flash Version - 1.3.0
Software Version - 1.0.2
Next Startup Image - Exist & OK
Image Name - image1.bin
Flash Version - 1.3.0
Software Version - 1.0.2
Backup Image - Exist & OK
Image Name - image2.bin
Flash Version - 1.3.0
Software Version - 1.0.3
POE+ works on FW 1.0.2 but getting these logs repeatably, ports 6 to 8 have nothing plugged in.
I've opened a SR with TP-Link, awaiting a response.
show logging buffer
#2021-12-06 20:30:22,[Port]/6/Reload port Tw1/0/6 phy firmware.
#2021-12-06 20:30:08,[Port]/6/Reload port Tw1/0/8 phy firmware.
#2021-12-06 20:29:54,[Port]/6/Reload port Tw1/0/7 phy firmware.
#2021-12-06 20:29:40,[Port]/6/Reload port Tw1/0/6 phy firmware.
#2006-01-01 08:03:21,[Port]/6/Reload port Tw1/0/7 phy firmware.
#2006-01-01 08:03:08,[Port]/6/Reload port Tw1/0/6 phy firmware.
#2006-01-01 08:02:57,[Port]/6/Reload port Tw1/0/5 phy firmware.
#2006-01-01 08:02:49,[Link]/5/Tw1/0/4 changed state to up.
#2006-01-01 08:02:46,[Port]/6/Reload port Tw1/0/4 phy firmware.
#2006-01-01 08:02:40,[Link]/5/Tw1/0/3 changed state to up.
#2006-01-01 08:02:35,[Port]/6/Reload port Tw1/0/3 phy firmware.
#2006-01-01 08:02:29,[Link]/5/Tw1/0/2 changed state to up.
#2006-01-01 08:02:24,[Port]/6/Reload port Tw1/0/2 phy firmware.
#2006-01-01 08:02:15,[Link]/5/Tw1/0/1 changed state to up.
#2006-01-01 08:02:13,[Port]/6/Reload port Tw1/0/1 phy firmware.
#2006-01-01 08:01:58,[Port]/6/Reload port Tw1/0/8 phy firmware.
#2006-01-01 08:01:45,[Port]/6/Reload port Tw1/0/7 phy firmware.
#2006-01-01 08:01:32,[Port]/6/Reload port Tw1/0/6 phy firmware.
#2006-01-01 08:01:05,[Port]/6/Reload port Tw1/0/8 phy firmware.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@WESPL To provide another data point, I have two of these TP-Link switches, and they both suffered this problem immediately after upgrading from v1.0.2 to v1.0.6. I downgraded both of the switches back down to v1.0.2, but only one of them has functional ethernet ports.
- Copy Link
- Report Inappropriate Content
I have the same problem here, the switch has become partially unusable after a reboot and fully unusable after a downgrade to the previous firmware. I even reset the switch but that doesn't help either. It just means I now have control back over my previously oc200 managed switch. I just see messages passing by via the serial console that the interfaces do either a PHY RESET or a PHY FW RELOAD. I can't find any means to get even one port up and running.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@WESPL I tried that, it is fully reset and the copper ports don't come up at all... and I don't have an SFP as alternative... :(
- Copy Link
- Report Inappropriate Content
Static IPs for WAN, yes. ER7206 or ER605 are multi-WAN routers.
Sounds like you need policy routing for the setup? Check out the link and let me know if this is what you want.
- Copy Link
- Report Inappropriate Content
@pgookin https://www.reddit.com/r/jackassforeverstreams/
- Copy Link
- Report Inappropriate Content
I've had a power outage, after power was back I now getting the same problem on 1.0.6, maybe that a clue to our problems, I've reopened my support case will see what they say.
- Copy Link
- Report Inappropriate Content
Has anyone found a resolution to this problem? I have downgraded to 1.0.2 and it seems that some ports work ok, but it seems to change which ports work on when I reboot.
- Copy Link
- Report Inappropriate Content
@Best Air Fryer Toaster Oven connect to TP-Link
Any update today? I'm having the same problem after upgrading to 1.0.6 and then downgrading back to 1.0.2, except none of my ethernet ports work.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 15019
Replies: 80
Voters 1
