Business Community > Controllers > LACP Issue
< Controllers

LACP Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

LACP Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
LACP Issue
LACP Issue
2022-05-11 08:34:24
Model: TL-SX3008F  
Hardware Version: V1
Firmware Version: 1.0

I have the TL-SX3008F using firmware version 1.0 and the TL-SG3428XMP using firmware 1.3 and am trying to set up lacp/lag on 2 of the 10G connections between them. Every time I do the TL-SG3428XMP freaks out, drops the connection, locks up, and stops working. The ports and sometimes the entire switch becomes unusable and I usually can't get it working again unless I plug the controller directly into one of the ports that were not set up for lacp and power cycle the switch.

  0      
 
  0      
 
#1
Options
9 Reply
Re:LACP Issue
2022-05-11 09:42:32

  @DigitalSteel 

 

Only to be sure. You first configured LAG before plug in the (second) cable?

  0  
  0  
#2
Options
Re:LACP Issue
2022-05-11 13:33:22 - last edited 2022-05-11 14:03:15

  @AndyGR42 Yeah, I set up LACP on both switches through the Omada controller for the ports that were going to be used before plugging any cables into them. I also have 2 other LACP connections, and a static LAG connection set up from the TL-SX3008F. Port 5+6 and port 7+8 are set up the same way and communicate with dual nic hyper-v servers and a Mikrotik switch uses a static LAG setup on Port 1+2 with no issues. I wanted to set port 3+4 to talk to port 25+26 on the the TL-SG3428XMP.

 

This is an example of how I have the connections set up.

I am using port 24 as the uplink to configure the switch, and then once it is set up, I disconnect it and plug my sfp+ cables in... and that is when the 45+ minute long process of trying to unbrick the switch occurs

  0  
  0  
#3
Options
Re:LACP Issue
2022-05-18 02:43:01

Dear @DigitalSteel,

 

DigitalSteel wrote

  @AndyGR42 Yeah, I set up LACP on both switches through the Omada controller for the ports that were going to be used before plugging any cables into them.

 

The Controller v5.0 has found an issue that the SFP+ ports can only work in 1G mode when LACP is configured, see more details from Here.

If you are using Controller v5.0 to configure LACP, it's suggested to upgrade your controller to v5.1 or later version and see if it works.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:LACP Issue
2022-05-18 03:02:41 - last edited 2022-05-18 03:04:56

  @Fae I am using controller version 5.3.1

I am not having an issue getting the 10G ports to operate at 10G mode. LACP and LAG work everywhere with no issues except only LACP with that one specific switch is an issue. Seems I have to wait for a firmware update according to the last post I saw.

  0  
  0  
#6
Options
Re:LACP Issue
2022-05-18 06:35:01

Dear @DigitalSteel,

 

DigitalSteel wrote

  @Fae I am using controller version 5.3.1

I am not having an issue getting the 10G ports to operate at 10G mode. LACP and LAG work everywhere with no issues except only LACP with that one specific switch is an issue. Seems I have to wait for a firmware update according to the last post I saw.

 

I see, you are already using the latest controller version (controller v5.1 is the earlier version), it seems that your case is different from the post I mentioned above. Could you please show me the last post you saw? I didn't notice other LACP issue on this forum. If it helps, I'd like to escalate your case to TP-Link support team for further investigation.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#7
Options
Re:LACP Issue
2022-05-18 13:05:41 - last edited 2022-05-18 13:08:17

  @Fae I just noticed it looks like the post was deleted. This is a screenshot of the email notification I got reguarding the post.

Although, now that I re-read both this post and your post, I am suspicious that this post was deleted because they thought it was actually the same problem you did at first and then realized it was actually something differrent.

  0  
  0  
#8
Options
Re:LACP Issue
2022-05-19 03:25:22

Dear @DigitalSteel,

 

DigitalSteel wrote

Although, now that I re-read both this post and your post, I am suspicious that this post was deleted because they thought it was actually the same problem you did at first and then realized it was actually something differrent.

 

Right, your case is different. We may need to know more detailed information for further troubleshooting.

 

From your previous description, it seems that there are 2 other LACP connections established successfully between the switches. But just the LACP connections between port 3+4 on TL-SX3008F and port 25+26 on the TL-SG3428XMP are failed. Is that right?

 

To better assist you, could you please upload your detailed network topology for checking?

Are you using TP-Link SFP + Modules? And what's their model number?

If possible, please elaborate on your configuration steps so that we can try to follow to reproduce and locate the issue.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#9
Options
Re:LACP Issue
2022-05-19 04:10:02 - last edited 2022-05-19 04:18:07

  @Fae Yes, that is correct. port 3+4 on TL-SX3008F and port 25+26 on the TL-SG3428XMP, when I enable LACP or LAG the TL-SG3428XMP becomes unresponsive.

I am using flyprofiber DACs that I bought here https://www.amazon.com/gp/product/B08YVTZXWS

 

This is the topology, currently I am using just regular cat6 to connect the TL-SG3428XMP to my Mikrotik CSS326-24G-2S+RM switch which has 2x10G connected to the TL-SX3008F using LAG. 

The Mikrotik switch is currently between the gateway and the other devices

  0  
  0  
#10
Options
Re:LACP Issue
2022-05-19 08:56:10 - last edited 2022-05-24 05:47:10

Dear @DigitalSteel,

 

DigitalSteel wrote

Yes, that is correct. port 3+4 on TL-SX3008F and port 25+26 on the TL-SG3428XMP, when I enable LACP or LAG the TL-SG3428XMP becomes unresponsive.

I am using flyprofiber DACs that I bought here https://www.amazon.com/gp/product/B08YVTZXWS

 

Thank you for your confirmation. I've reported the case to the R&D team for checking.

 

May I know the detailed firmware version of your TL-SX3008F and TL-SG3428XMP switches?

Navigate to Devices page, click on the specific switch for Details -> Overview, where you will find Firmware Version such as 3.20.2 Build 20210806 Rel.55686

 

Edit: Still awaiting your firmware version.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 1613

Replies: 9

Related Articles
 LACP issue after REBOOT
643 0
TL-SG2008P LACP issue with Synology DS220+
2639 0
SG2210P LAG LACP ?
785 0
LACP not prioritizing desired ports
1343 0
Omada Controller LACP problem
3229 0
 lacp support
1004 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.