Business Community > Business Routers > ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP
< Business Routers

ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP
ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP
2022-07-12 13:41:55 - last edited 2022-08-31 03:39:44
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version: 1.2.0

My setup is

 

FTTH ONT->ER605->SG2008P->OC200 (etc.)

 

I have configured a VLAN which is attached to a guest SSID and has a WAN policy route via an L2TP VPN.  Wireless clients connected to the guest SSID are recognized and reported correctly.  However, I have two LAN ports on the ER605 (WAN3 + LAN) which are configured to belong the same VLAN and wired clients connected to these ports are NOT recognized nor reported on as clients, nor is the traffic they generate reported via the OC200 in Dashboard->Summary graphs (ie ISP Load etc.).

<< Just doing a little community service while hanging around waiting for the ER605v1 1.3.0 firmware to drop >>
  0      
 
  0      
 
#1
Options
3 Reply
Re:ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP
2022-07-13 08:07:57 - last edited 2022-08-31 03:39:44

  @d0ugmac1 

 

If you reboot the controller does that fix the problem?
Does this problem occur after you set up a guest network or VLAN?
Was it displayed normally before?
Are you connecting to two clients that are powered on and transmitting data?

  0  
  0  
#2
Options
Re:ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP
2022-07-13 15:33:27 - last edited 2022-08-31 03:39:44
My ER605 went la-la and had to be rebooted. This caused another bug whereby the VLAN'd device hardwired to the switch jumps onto the wrong VLAN when rebooted (LAN port cannot be removed from VLAN1). So it will be a while before I can recreate the conditions and provide more detail on this one. The problem occurs on a device hardwired to the ER605 which is assigned an IP belonging to a non-default VLAN which is also considered a Guest network, and whose uplink is via an L2TP tunnel.
<< Just doing a little community service while hanging around waiting for the ER605v1 1.3.0 firmware to drop >>
  0  
  0  
#3
Options
Re:ER605 Reporting BUG - doesn't report wired VLAN clients egressing via L2TP
2022-08-03 13:02:43 - last edited 2022-08-31 03:39:44

  @d0ugmac1 

 

With the device hardwired to an SG2008P port instead of the ER605 port, the usage reporting is correct (OC200 v 5.3.2, ER605 1.2.1)

 

Until we have more flexibility with the 4 LAN-capable ports on the ER605 (ie remove VLAN1), I cannot revert my setup to test further.

<< Just doing a little community service while hanging around waiting for the ER605v1 1.3.0 firmware to drop >>
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 109

Replies: 3

Related Articles
How do I report Bugs to Firmware Team
681 0
ER605 V2_2.1.1 Official Firmware (Released on Jan 30th, 2023)
2539 3
ER7206, v5.9.9 and L2TP clients
92 0
ER8411 V1_1.0.3 Official Firmware (Released on Mar 17th, 2023)
125 0
ER7206 V1_1.3.0 Official Firmware (Released on Mar 28th, 2023)
914 1
ER8411 V1_1.0.2 Official Firmware (Released on Jan 30th, 2023)
583 1
About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.