Business Community > Routers > LAN-to-LAN IPsec Multiple subnets not working
< Routers

LAN-to-LAN IPsec Multiple subnets not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

LAN-to-LAN IPsec Multiple subnets not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
LAN-to-LAN IPsec Multiple subnets not working
LAN-to-LAN IPsec Multiple subnets not working
2022-12-19 13:58:15 - last edited 2022-12-22 14:54:18
Tags: #VLAN & Multi-Networks
Model: ER7206 (TL-ER7206)  
Hardware Version:
Firmware Version:

Hello,

 

I have two remote sites.
I connected the 2 sites with an IPSEC tunnel

 

Communication is ok between vlan 1 (10.31.6.X) of site 1 and vlan ( 10.64.23.x) 1 of site 2.

 

However, I cannot communicate between vlan 2 (10.174.1.x) of site 1 and vlan 1 ( 10.64.23.x) of site 2

I configured the ipsec tunnel on the 2 routers

 

Router site 2

 

 

Router site 1

In the ipsec SA, I find that the second link, is not ok on the 2 routers

 

 

I don't see where the error could come from, have you ever had the case?

 

I've been pulling my hair out for 2 weeks '(

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:LAN-to-LAN IPsec Multiple subnets not working-Solution
2022-12-19 15:03:17 - last edited 2022-12-19 15:03:22

  @Yan1245 

 

 

Typing error in my rules

Recommended Solution
  0  
  0  
#3
Options
4 Reply
Re:LAN-to-LAN IPsec Multiple subnets not working
2022-12-19 14:10:23 - last edited 2022-12-19 14:11:48

 

Tracert nok between vlan 2 (10.174.1.X) of site 1 and vlan 1( 10.64.23.x)  of site 2.

 

Tracert ok between  vlan 1 ( 10.64.23x) of site 2 and vlan 1 ( 10.31.6. X) of site 1

  0  
  0  
#2
Options
Re:LAN-to-LAN IPsec Multiple subnets not working-Solution
2022-12-19 15:03:17 - last edited 2022-12-19 15:03:22

  @Yan1245 

 

 

Typing error in my rules

Recommended Solution
  0  
  0  
#3
Options
Re:LAN-to-LAN IPsec Multiple subnets not working
2022-12-20 06:12:18

  @Yan1245 

If I'm not wrong, in standalone it's impossible.

 

You will need the Omada controller, to add multi-nets to the Ipsec rule.

  0  
  0  
#4
Options
Re:LAN-to-LAN IPsec Multiple subnets not working
2022-12-22 14:53:26 - last edited 2022-12-22 14:53:42
I have an omada controller at each site, but I find them quite unstable, so I don't associate the routers.

I managed to configure it in standalone, it's slightly more complicated than with the omada
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 650

Replies: 4

Tags

VLAN & Multi-Networks
Related Articles
 How to configure IPSec LAN to LAN VPN for multiple subnets
1066 0
 Multiple LAN subnets
510 0
IPsec Policy with two remote subnets
1089 0
VPN Client to Lan on multiple subnet
1198 0
Portail LAN
155 0
ER7206 Gateway ACL LAN-LAN IPGroup
2235 20
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.