Business Community > Routers > OC200, ER7206 and Netgear Switches
< Routers

OC200, ER7206 and Netgear Switches

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

OC200, ER7206 and Netgear Switches

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
OC200, ER7206 and Netgear Switches
OC200, ER7206 and Netgear Switches
2023-01-17 17:37:31
Tags: #VLAN & Multi-Networks
Model: ER7206 (TL-ER7206)  
Hardware Version: V1
Firmware Version: 1.2.3

So I'm try to figure out if I can use the OC200, ER7206 with my Netgear switches and setting up vlans.  I'm using Netgear's GC110 which are suppose to be L2/L3.  I'm still very much a newbie so I don't have a complete understanding of compatibility between different manufactures.   

  0      
 
  0      
 
#1
Options
5 Reply
Re:OC200, ER7206 and Netgear Switches
2023-01-17 18:51:39

  @C.Conklin 

 

They all support IEEE 802.1Q VLAN Tagging so you should be able to make it work. In my VLAN network, I have a mix of TP-Link, Netgear and CISCO devices and I have not experienced any compatibility issues so far.

Kris K
  0  
  0  
#2
Options
Re:OC200, ER7206 and Netgear Switches
2023-01-18 14:29:51

  @KJK  I think my problem is the Omada controller software does not assign PVIDs or at least not that you can't manually assign them.  So, I'm either missing something or must buy a switch that will work with the Omada software or use my ER7206 as a standalone device.

  0  
  0  
#3
Options
Re:OC200, ER7206 and Netgear Switches
2023-01-18 14:43:41

  @C.Conklin 

 

I'm using my ER7206 standalone so I can't help you to set it up in Omada. However, I'm pretty sure it can be done. There is no need to buy any new equipment just because of these configuration difficulties.

Kris K
  0  
  0  
#4
Options
Re:OC200, ER7206 and Netgear Switches
2023-01-26 10:40:48

  @C.Conklin 

You can assign PVID with Omada Controller. It's on the Settings->Wired Network-> Profile.

Native Network means the PVID for this profile.

  0  
  0  
#5
Options
Re:OC200, ER7206 and Netgear Switches
2023-02-16 19:16:03

  @C.Conklin Got it figured out.  Very new to vlans so I still have a lot of learning to do.  Then add in using the Omada Controller, Netgears Insight cloud management and slightly different terminology makes my head hurt.

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 628

Replies: 5

Tags

VLAN & Multi-Networks
Related Articles
ER7206 Trunk Vlan with TL-SG108E
1726 0
 OC200+ER7206 unknowk password
520 0
 ER7206 and OC200 wallmount options
742 0
OC200 and change of router from ER605 to ER7206
97 0
ER7206 v1 will not adopt in Omada Controller
1561 0
Standalone ACL on ER7206 V1 not working
675 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.