Strange behaviour with Omada and ISP Load

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Strange behaviour with Omada and ISP Load

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Strange behaviour with Omada and ISP Load
Strange behaviour with Omada and ISP Load
2023-02-14 19:42:25 - last edited 2023-02-14 20:11:51
Model: ER7212PC  
Hardware Version: V1
Firmware Version: 1.0.2 Build 20230202 Rel.10719

Im seeing some strange behaviour since updating from 1.0.1 -> 1.0.2. I have 2 seprate internet lines. One is fiber and the other is using a 4g router on a mobile network, My question is while they might be issues with one line how come the drops are displayed on both seprate wan lines at the same time from 2 diffrent ISP's. I have had no issues with the internet connections on both ISP's just was wondering why it drops to 0ms at random intervials on both ISP's. Anyone else come across this?

 

ISP Load

Many Thanks

Archer MR600 V1 3G/4G ER7212PC v1.0 TL-SG2210P v5.0 4 x EAP653(EU) v1.0
  0      
  0      
#1
Options
5 Reply
Re:Strange behaviour with Omada and ISP Load
2023-02-15 08:29:39

Dear @TazDevilLooney ,

 

Thank you so much for taking the time to report the issue to our community!

1. Did this issue infect the actual usage of ER7212PC?

2. Did this issue occur after firmware updated to 1.0.2?

3. The issue you mentioned is related to the points marked in the picture, right?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:Strange behaviour with Omada and ISP Load
2023-02-15 12:20:16 - last edited 2023-02-15 22:23:35

  @Hank21 

 

Hi Hank, The points marked in the picture is what i wanted to discuss. This started to happen with the 1.0.2 update as i had not noticed it on the 1.0.1. I've have had no problems with internet dropping and everything is runs smoothly. It looks to be just cosmetic at this point. I only run a basic setup for internet use only. I don't use VPN, Dynamic DNS or port forwarding and i don't host anything. If it might affect them services i wouldn't know at this point. I'm just running a ER7212PC v1.0 / 1.0.2 Build 20230202 Rel.10719 and 3 x EAP653(EU) v1.0 / 1.0.4 Build 20220921 Rel. 73428. I have no switch attached as i was trying to localize the problem. 2 different ISP and services. My lan service is on a double nat and my 4g service is a bridge connection to Three mobile (Huawei CPE Pro Router 5G H112-372)

 

 

Map-10

 

Archer MR600 V1 3G/4G ER7212PC v1.0 TL-SG2210P v5.0 4 x EAP653(EU) v1.0
  0  
  0  
#3
Options
Re:Strange behaviour with Omada and ISP Load
2023-03-27 18:15:42 - last edited 2023-03-27 18:16:37

  @TazDevilLooney 

 

Im, still having the problem with the new 1.0.3 Build 20230314 Rel.21018. I'm also getting connection drops to. I've tryied diffrent DNS and Changed the Oneline Detection Interval. The issue has increased in fequency since upgrading from 1.0.2 and causing ping drops now. I've tried multiable restarts and can not find the cause.

 

ISP Load

 

CPU Load

 

 Ping Test

 

Any ideas?

 

Regards

Archer MR600 V1 3G/4G ER7212PC v1.0 TL-SG2210P v5.0 4 x EAP653(EU) v1.0
  0  
  0  
#4
Options
Re:Strange behaviour with Omada and ISP Load
2023-03-29 05:44:47

Hello @TazDevilLooney ,

 

May I know how many client devices are behind the ER7212PC in your network total?

Are there any high-traffic applications on the back-end devices?

 

Do you have Internet intermitted issues frequently?

Can you confirm if your ISP network is stable?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:Strange behaviour with Omada and ISP Load
2023-03-29 05:46:34

  @TazDevilLooney 

 

Hi, dude, your issue is weird, if you think this issue start after the firmware was upgraded, have you tried back to the 1.0.1 version for testing?

Just striving to develop myself while helping others.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 402

Replies: 5

Related Articles