EAP653 disconnect/provisioning loop after loss of power
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.EAP653 disconnect/provisioning loop after loss of power
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello all,
I currently want to equip the site with EAP653 APs and have already installed them everywhere.
However, if I disconnect one of the APs from the power to connect them somewhere else or because of a power failure etc. then the EAP is in the Omada controller as offline, then as provisioning and so on.
The only way to fix this is to reset the device and set it up again.
This is simply not an option with the amount of devices used.
I ask for a timely solution, otherwise we exchange all devices for devices from other manufacturers.
Router: ER605 v1.0 1.2.1 Build 20220512 Rel.76748
Controller: OC200 1.0 1.21.7 Build 20221206 Rel.58608
This is an intolerable state of affairs.
Best regards
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hello @aurevo
Sorry for any trouble caused! The issue will be fixed in the subsequent firmware soon. Before the new firmware is released to fix the issue, you may follow this solution post for a temporary solution.
- Copy Link
- Report Inappropriate Content
Hello @aurevo,
Sorry for any trouble caused!
To precisely locate the issue, please tell us more details as follow:
1. How many EAP653s do you have? How did you connect them?
2. Please provide your Network layout. (You can draw a diagram of Network Topology simply if you don't mind.)
3. How is the EAP powered?
By using the POE switch or using the POE power adapter, and what is the distance from the POE switch/ adapter to the EAP device?
4. If you disconnect one of the APs from the power and do not connect them somewhere else, still connect it to the current cable/place, is the issue reproduced?
- Copy Link
- Report Inappropriate Content
Hi Hank, thanks for you quick response.
Aktually I have 6x EAP653, 4 connected and planning to buy a lot more. So they have to be stable and without problems.
Each AP is connected via cable on a TL-PoE150S.
ER605 -> 1 or more TP-Link switches without PoE -> TL-PoE150S -> EAP653
This is similar to all installations.
The distance is actually for testing purposes maximum 20m.
Tested with different cables from 0,5m to 20m.
4. If I disconnect ethernet, the device is powered off and directly goes to the loop.
- Copy Link
- Report Inappropriate Content
Hi @aurevo
It looks like EAP653 Mesh (which is auto-enabled) made some conflict with the controller. Please help me check the 5Ghz channels that your EAP653 are using, are they DFS channels like 120,124, or 128?
If that is the thing, a simple temporary solution:
On Omada Controller Devices list, choose the loop adopting issue EAP and hit Forget;
The EAP Status will turn to "Managed by other" on the Controller;
Wait 10 mintues, then adopt this EAP again.
- Copy Link
- Report Inappropriate Content
1. 124 / 5620MHz
2. 116 / 5580MHz
3. 128 / 5640MHz
4. 128 / 5640MHz
What does temporary solution means? Is the error fixed or will it come up again?
And what is the permanent solution for this error?
- Copy Link
- Report Inappropriate Content
Hank21 wrote
Hi @aurevo
It looks like EAP653 Mesh (which is auto-enabled) made some conflict with the controller. Please help me check the 5Ghz channels that your EAP653 are using, are they DFS channels like 120,124, or 128?
If that is the thing, a simple temporary solution:
On Omada Controller Devices list, choose the loop adopting issue EAP and hit Forget;
The EAP Status will turn to "Managed by other" on the Controller;
Wait 10 mintues, then adopt this EAP again.
This time I disconnected power and tried your solution.
When provisioning I hit Forget and got an error message similar to "AP removed, but controller could not reset it, manual reset is necessary for adopting it again."
So I hat to reset it and to set up again.
That was the exactly same situation as before.
And this is no solution I can use for 20 or more APs, which hang under the ceiling or roofs.
There is no easy possibility to reset and that also is no resolution.
- Copy Link
- Report Inappropriate Content
Hi @aurevo
You don't have to reset the EAP manually, even though it shows the controller cannot reset it.
Just hit "Forget" on the controller and ignore the error message. Wait 10 minutes the AP will turn to "Managed by others" status on the Controller. Then you can re-adopt it.
- Copy Link
- Report Inappropriate Content
Hello @aurevo
Sorry for any trouble caused! The issue will be fixed in the subsequent firmware soon. Before the new firmware is released to fix the issue, you may follow this solution post for a temporary solution.
- Copy Link
- Report Inappropriate Content
I agree this is an unacceptable situation.
I set up a new set of TP-Link kit including controller, Firewall, Switch and 3 EAP610 Mesh.
Just like user aurevo experienced, I set up the whole thing and it was working well. Next day I powered off on EAP for 10 minutes and it wouldn't reconnect. I installed the Beta firmware fix, all to do with Radar channels. Seemed to work OK so I did a full reset on all kit, started again. All fine for 2 days then I tried a power cycle and again it wouldn't reconnect. I went through multiple attempts to readopt, forget, wait. Just ridiculous.
I suspect the trouble started when I first unboxed the kit last week. I let the controller adopt everything then it prompted for Firmware updates, which is good practice, so I did that. Maybe if I hadn't "upgraded" it might have been OK.
What I don't understand is how TP-Link can leave disasterous firmware out there to be installed and prompting to install it. Why not take this version down for now until there is a fix?
This controller stuff is floored and untested. The obsession with the controller is the only way to manage it after its adoption means there is no way for me to find out what's wrong. If it was still possible to go to the EAP's admin page, even to look at settings, that would help.
Sad really because I've used TP-Link kit for many years. Each individual piece has been reliable. Now with the controller in the picture it all breaks.
The EAP610 has a really annoying feature which shows when the EAP is not connected. It flashes the only LED - 5 seconds on, half a second off, 5 seconds on etc. This means I find myself staring at the EAP thinking it might be working but then not. Why not flash in the true sense of the word.
In a couple of days I'm returning the whole lot for a full refund.
If I hear back a proper offer of help from TP-Link I will continue to work on the issue.
- Copy Link
- Report Inappropriate Content
Hello @Fae,
is there also a firmware for EAP225 v5.0 indoor to fix the issue? I could not find it.
I ask because I have the same problem with two EAP225 v5.0 indoor https://www.tp-link.com/uk/business-networking/ceiling-mount-ap/eap225/
One is wired and the other one connects wireless. Everything works as a charm but after a reboot or power loss, it just shows as "Disconnected" and won't connect unless I forget it, then factory reset it and re-adopt it.
I have an OC200 running the latest version 5.9.32
EAP225 v5.0 also latest version 1.1.3
These are my site settings.
Thanks in advance!
Best Regards
- Copy Link
- Report Inappropriate Content
Hello @jruk,
May I know the firmware version of your EAP610?
Did the EAP610 fall into adoption loop (loop in adopting-> configuring-> heartbeat missed-> disconnected) or stuck in "Disconnected" state after you do a physical reboot?
Did this issue happen when the EAPs were in the DFS Channel (120, 124, or 128)?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2211
Replies: 12
Voters 0
No one has voted for it yet.