ER605 V1_1.2.3 Beta Firmware causing Router Disconnects

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER605 V1_1.2.3 Beta Firmware causing Router Disconnects

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
22 Reply
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-20 20:44:47

@Fae Why there is only a Beta firmware for 605 v.1.0 and not aslo for version 2.0?

 

  0  
  0  
#12
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-21 03:45:27

Hello @RoRovDongen 

 

The ER605 V1 1.2.3 Beta firmware added some new features like Stateful ACL and mDNS Repeater, which have already been supported on ER605 V2 2.1.1 and above official firmware.

 

Do you need a Beta firmware for ER605 v2? Why? Do you have any issues with the ER605 V2? 

What's the current firmware version of your ER605?

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#13
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-21 21:01:57

  @Fae 

 

The problems we currently have:

- AI optimazation isn't working.

- DHCP reservation isn't working fine.

- Can't reserve a specific port to a new Vlan ID.

 

Current versions are:

- 605 v2.1.2.

- OC200 v5.7.6.

- EAP610 v1.1.0.

  0  
  0  
#14
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-21 21:40:50

  @RoRovDongle

Appreciate you are having issues with a version  2 ER605, but please start your own thread so this version 1 post is not diluted/hijacked.

  0  
  0  
#15
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-21 22:12:52
So, these problems are only on version 2 of the R605?
  0  
  0  
#16
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-21 23:02:26

  @RoRovDongen

Have no idea. But this thread is about beta firmware , that is only for ER605 version 1 hardware.

  0  
  0  
#17
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-22 01:34:33

Hello @RoRovDongen 

 

Please feel free to start a new thread here, and try to elaborate on the problem so that we can better understand what happened and try to help you out.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#18
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-03-31 17:51:08 - last edited 2023-04-03 16:42:38

  @1207 

 

Reloaded the beta firmware (ER605 V1_1.2.3  Beta Firmware) and the router disconnected after 20 hours.  Clients couldn't get an IP address and had no access to the web.  The memory utilization increased over the 20 hours and after rebooting the router the memory precentage dropped. See attached image. Let me know if you need more data.

 

 

  

  0  
  0  
#19
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-04-03 06:02:03

Hello @1207 

 

Did you upgraded to the ER605(UN)_V1_1.2.2 Build 20230328 (Beta) which has added the fix of the disconnected issue caused by mDNS? If not, could you please give it a try?

 

If you're already using the 1.2.2 Build 20230328 Beta but still have the disconnected issue, please confirm whether the mDNS is enabled, and whether the issue would be gone after mDNS is disabled.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#20
Options
Re:ER605 V1_1.2.3 Beta Firmware causing Router Disconnects
2023-04-03 16:48:53 - last edited 2023-04-11 19:43:17

  @Fae 

 

Edit:  When I replied below, my assumption was that version 1.2.3 beta firmware was a later version of router firmware then 1.2.2. I finally realized that 1.2.2 was released after 1.2.3.  I've installed firmware 1.2.2 and so far the router memory has not increased and mDNS is activated. 

 

No, I've never loaded or seemed to need firmware 1.2.2.  The memory increase image that I posted above was from when version 1.2.3 beta was loaded, and yes mDNS was activated.

 

I went back to the last official release ER605 V1_1.2.1 Firmware, with mDNS activated and I'm not seeing any router disconnects or memory increase (see image below).

 

  

  0  
  0  
#21
Options
Related Articles