Business Community > Requests & Suggestions > WireGuard Client-to-Site
< Requests & Suggestions
 
16
Votes

Implemented WireGuard Client-to-Site

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12
 
16
Votes

Implemented WireGuard Client-to-Site

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ImplementedWireGuard Client-to-Site
WireGuard Client-to-Site
2023-03-15 10:40:27 - last edited 2023-09-04 05:31:01
Tags: #WireGuard
Model: Omada Software Controller (Linux)  
Hardware Version:
Firmware Version:

Hello guys,

 

WireGuard is available on Omada SDN. And that's great - I love it.

 

But I'm missing the feature to configure client-to-site connections with WireGuard. This option is only available for other VPN protocols like OpenVPN.

 

Many VPN providers use WireGuard. I think adding the ability to connect via WireGuard would be a big improvement. This is of course already possible with OpenVPN, but the throughput is very low.

 

Maybe there will be a way to add this feature to one of the upcoming versions.

 

Best regards

Pascal

#1
Options
1 Accepted Solution
Re:WireGuard Client-to-Site -Solution
2023-03-22 05:35:16 - last edited 2023-03-22 05:35:23

Hello @pascal585 

 

pascal585 wrote

Many VPN providers use WireGuard. I think adding the ability to connect via WireGuard would be a big improvement.

 

If you're trying to connect ER605 V2 as the WireGuard VPN client to connect a remote WireGuard VPN service and support proxy Internet (make all the Internet traffic be routed through the VPN tunnel), please follow the post below for the available solution.

 

Solution to ER605 V2 as WireGuard VPN “Client” Failed to Support Proxy Internet

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
#9
Options
14 Reply
Re:WireGuard Client-to-Site
2023-03-15 11:46:30

+1

 

pfSense --> TL-SX3008F L3 --> Omada -->
#2
Options
RE:WireGuard Client-to-Site
2023-03-15 13:12:03
pls!
#3
Options
Re:WireGuard Client-to-Site
2023-03-15 18:45:30

+1

#4
Options
RE:WireGuard Client-to-Site
2023-03-18 12:59:55
+1
#6
Options
Re:WireGuard Client-to-Site
2023-03-21 22:03:47
+1
#7
Options
RE:WireGuard Client-to-Site
2023-03-21 22:07:33
important
#8
Options
Re:WireGuard Client-to-Site -Solution
2023-03-22 05:35:16 - last edited 2023-03-22 05:35:23

Hello @pascal585 

 

pascal585 wrote

Many VPN providers use WireGuard. I think adding the ability to connect via WireGuard would be a big improvement.

 

If you're trying to connect ER605 V2 as the WireGuard VPN client to connect a remote WireGuard VPN service and support proxy Internet (make all the Internet traffic be routed through the VPN tunnel), please follow the post below for the available solution.

 

Solution to ER605 V2 as WireGuard VPN “Client” Failed to Support Proxy Internet

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
#9
Options
Re:WireGuard Client-to-Site
2023-03-22 09:36:26

  @Fae 

 

Thank you very much for your hint.

 

In my case, I don't want to route all internet traffic through WireGuard VPN, just a single VLAN with its devices.

As far as I know, this option only exists with OpenVPN or similar, but not with WireGuard.

 

I would be very happy if the functionality of WireGuard was expanded.

#10
Options
RE:WireGuard Client-to-Site
2023-03-22 10:06:49
+1
#11
Options
Re:WireGuard Client-to-Site
2023-03-28 13:45:21

+1

#12
Options
12

Information

Helpful: 16

Views: 1492

Replies: 14

Voters 14

voter's avatar
voter's avatar
voter's avatar
voter's avatar
+ 10 Voters

Tags

WireGuard
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.