TP Link ER7206
Hello
I have get big problems now with my er7206, its rebooting all over, several times every day,
i have test different firmware ( 3 latest), have reset it several times, checked the settings lite 1000 times.
i have test with SFP port and no change, starting to lose my maid here :(
and i cant find eny error report or message from the router.
So how can jag proceed?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
i think i have fixed the problem, i did reset the hole shabang... lite much to handle but i only did tek 1 day to get all to worked agin :)
So i did reset all my gear.
1st ER7206
4st EAP225
1st EAP 653
2st EAP 610
4st SG105PE
i didn't what to use my backup when i didn't now what caused the problems, so now i just hope it works :)
- Copy Link
- Report Inappropriate Content
So there is absolutely nothing curious in the logs? If not, my guess would be a power supply issue.
- Copy Link
- Report Inappropriate Content
@d0ugmac1 Hello
i run controller 200 så i don't find the picture you showing me, ER7206 don't have any power supply that i can change, only one kabel,
- Copy Link
- Report Inappropriate Content
Ok, so the OC200 version looks like:
Sounds like you are running your OC200 via POE..which means you must have a POE switch in your setup as well?
I would keep the 5.7.6 firmware on the OC200 for now, forget and then re-adopt the ER7206. If that doesn't work, you can try factory defaulting the OC200 (take a backup first) and rebuild a minimal config to get you back up and running again (ie WAN settings, LAN settings, leave ACLs, port forwards for now...this is just a stability test), then factory reset the ER7206 and do a clean adoption.
Since the ER7206 has an AC input, if there is a PSU issue it will be internal and not user fixable. The only suggestion I have here is bring power from another circuit somewhere with an extension cord in case there is some 'noise' on the current plug/circuit (like a big motor starting up (fridge, freezer, furnace...) or a welder or....??)
The quickest fix may be just to purchase a new 7206 if you are unable to resolve by defaulting and rebuilding the soft configuration.
- Copy Link
- Report Inappropriate Content
the picture is the same that i have. i have tested 3 latest firmware on 7206 i have resettet it sevral times i have testat whith an without SFP module i have put a fan that blows air on it 7206 i dont have tested any firmware in OC200, it runs 5.7.6 yes i have 4 poe switchs and they work, its only the router that ceep rebooting. and i cant faind any logs that can be the router problems and what i can remember i havet chage anyfhing on my setup i moths
only one thing i can rember that i have done now is put upp nginx proxey manager, can that mess upp my router?
- Copy Link
- Report Inappropriate Content
Well, it sounds like a hardware fault then. Recommend you open a support ticket with TPlink to confirm.
- Copy Link
- Report Inappropriate Content
Looks like the ER7206 comes with a Limited Lifetime Warranty. That at least is good news.
- Copy Link
- Report Inappropriate Content
I have change the router now to my old er605 V2 and its working now, so my 7206 is prtobley broken :(
- Copy Link
- Report Inappropriate Content
i think i have fixed the problem, i did reset the hole shabang... lite much to handle but i only did tek 1 day to get all to worked agin :)
So i did reset all my gear.
1st ER7206
4st EAP225
1st EAP 653
2st EAP 610
4st SG105PE
i didn't what to use my backup when i didn't now what caused the problems, so now i just hope it works :)
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 649
Replies: 8
Voters 0
No one has voted for it yet.