ER605 Site to Site Wireguard setup

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER605 Site to Site Wireguard setup

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER605 Site to Site Wireguard setup
ER605 Site to Site Wireguard setup
2023-08-27 03:50:34 - last edited 2023-08-29 06:40:16
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.1.4

Hi TP Link Community

 

I'm trying to set up a Site to Site virtual network using the ER605 on one side and a Wireguard Server on the other. The Wireguard server is working for P2S connections from individual clients. 

 

Has anyone been able to achieve this, I'm pulling my hair out trying as it seems like the Wireguard config on the ER605 only allows it to act like a server and not a client also although I may be misunderstanding something with the config. 

 

I can successfully configure it to handshake but the traffic doesn't pass between the sites properly.

 

 

Charles

  0      
  0      
#1
Options
1 Accepted Solution
Re:ER605 Site to Site Wireguard setup-Solution
2023-08-29 05:29:52 - last edited 2023-08-29 06:40:16
ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
Recommended Solution
  0  
  0  
#5
Options
4 Reply
Re:ER605 Site to Site Wireguard setup
2023-08-28 03:18:10

  @ChuckyP 

it's all about the config. 

for the wireguard, there isn't a thing server or client. it all depends on your parameters.

if you want someone else to help you troubleshoot, post the config here and your network diagram. 

https://community.tp-link.com/en/business/forum/topic/619652

ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
  0  
  0  
#2
Options
Re:ER605 Site to Site Wireguard setup
2023-08-28 07:04:01

Hi @Tedd404, thanks for the reply. This editor won't for the life of me let me post (blocks it) but I've attached what I was trying to send in this pdf with all the config... 

 

Thanks to anyone that can help

File:
TPLink VPN.pdfDownload
  0  
  0  
#3
Options
Re:ER605 Site to Site Wireguard setup
2023-08-29 01:02:20

  @ChuckyP 

anyway it looked kinda messy.

 

 

just point you in the right direction:

all you have to do is to set the correct allowed IP address. in the peer settings, allowed IPs are set to be your dst allowed ip addresses. so you have to specify that correctly, anything else would be the same as client connection. 

ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
  0  
  0  
#4
Options
Re:ER605 Site to Site Wireguard setup-Solution
2023-08-29 05:29:52 - last edited 2023-08-29 06:40:16
ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
Recommended Solution
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1091

Replies: 4

Related Articles