Home

Forums

Stories

Knowledge Base

Business Community > Routers > ER7206 WAN throughput via SNMP

< Routers

ER7206 WAN throughput via SNMP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER7206 WAN throughput via SNMP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

JarekPrzybyl

2023-10-09 08:03:39 - last edited 2023-10-12 01:06:44

Posts: 10

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2023-09-27

ER7206 WAN throughput via SNMP

2023-10-09 08:03:39 - last edited 2023-10-12 01:06:44

Tags: #SNMP

Model: ER7206 (TL-ER7206)

Hardware Version: V1

Firmware Version: 1.3.0 Build 20230322

I saw few similar topics but I have to make next one, because it is still unclear to me.

Goal is to read WAN Rx and Tx throughput via SNMP. Could anybody tell me what OIDs give such parameters?

By own I found only these:

It seems I have only basic interface parameters (state, negotiated/configured speed, etc) and counters, but not throughput. Needed parameters are visible in GUI, so I believe it should be also available via SNMP. Any help will be appreciated.

1 Accepted Solution

KJK

LV4

2023-10-10 03:16:58 - last edited 2023-10-12 01:06:44

Posts: 317

Helpful: 116

Solutions: 31

Stories: 0

Registered: 2022-03-29

Re:ER7206 WAN throughput via SNMP-Solution

2023-10-10 03:16:58 - last edited 2023-10-12 01:06:44

@JarekPrzybyl

That would need to be calculated from these counters.

1.3.6.1.2.1.2.2.1.16.1049 [ifOutOctets.1049]
1.3.6.1.2.1.2.2.1.10.1049 [ifInOctets.1049]

Note that these counters are not the same as the GUI Total TX Bytes or Total RX Bytes. The SNMP counters can't be cleared.

Kris K

Recommended Solution

JarekPrzybyl

LV1

2023-10-10 20:16:20

Posts: 10

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2023-09-27

Re:ER7206 WAN throughput via SNMP

2023-10-10 20:16:20

KJK wrote

That would need to be calculated

So, no way, to read just a value displayed by GUI? It will complicate my life a bit, but okay, thx!

KJK

LV4

2023-10-11 03:04:26

Posts: 317

Helpful: 116

Solutions: 31

Stories: 0

Registered: 2022-03-29

Re:ER7206 WAN throughput via SNMP

2023-10-11 03:04:26

@JarekPrzybyl

Not to my knowledge and I actually don't expect it. It would be waisting of resources most of the time in my opinion.

Kris K

KimcheeGUN

LV4

2023-10-11 13:09:17 - last edited 2023-10-11 13:09:39

Posts: 603

Helpful: 281

Solutions: 42

Stories: 0

Registered: 2022-07-05

Re:ER7206 WAN throughput via SNMP

2023-10-11 13:09:17 - last edited 2023-10-11 13:09:39

@JarekPrzybyl

I use Observium against my Omada network and it shows wan speed data fine. I would suggest switching SNMP apps.

I can not teach anyone anything - I can only make them think - Socrates

JarekPrzybyl

LV1

2023-10-11 16:37:37 - last edited 2023-10-11 17:08:48

Posts: 10

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2023-09-27

Re:ER7206 WAN throughput via SNMP

2023-10-11 16:37:37 - last edited 2023-10-11 17:08:48

@KimcheeGUN

Ok, thanks for this info, I'll check.

[edit]

I have checked. Not with your sw, but with trial of PRTG and indeed: i see rx and tx current throughput on Eth1. But still unclear for me is, if this is an exact value taken by SNMP from my router or maybe it is calculated by PRTG from counters? I'm not familiar with this software, can't find what OID is displayed.

My goal is to have OID needed value and use it in other project (Home Assistant).

JarekPrzybyl

LV1

2023-10-11 22:15:39

Posts: 10

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2023-09-27

Re:ER7206 WAN throughput via SNMP

2023-10-11 22:15:39

Finally I did it as @KJK adviced, measurement is working fine, thanks!

ER7206 WAN throughput via SNMP

ER7206 WAN throughput via SNMP

Information

Voters 0

Tags