Incorporating Omada SDN with existing 10G Hardwares

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Incorporating Omada SDN with existing 10G Hardwares

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Incorporating Omada SDN with existing 10G Hardwares
Incorporating Omada SDN with existing 10G Hardwares
2023-10-30 04:37:26 - last edited 2023-11-09 01:41:01
Hardware Version:
Firmware Version:

Hi everyone,

 

I'm planning to incorporate Omada SDN ecosystem into a pre-existing config for a video editing company I'm working under at the moment. I have done some research and come up with a simple network topology that I hope would work. I would appreciate it if you would take a look at what I come up with and see if there's anything I miss or could do better.

 

I'm just not familiar with Omada SDN and afraid that I'd make the wrong purchase. 😔

 

Thank you for your time. 🙏🙏

 

My Network Requirement : 

- Facilitate 10G speed for server and editing suite

- 3 VLANs for editing suite, staffs, and guests

- Can facilitate up to 200-ish devices.

 

network topology

  0      
  0      
#1
Options
1 Accepted Solution
Re:Incorporating Omada SDN with existing 10G Hardwares-Solution
2023-10-31 06:43:26 - last edited 2023-11-09 01:41:01

Hello @deo2888,

 

Based on your requirements and descriptions, the 10G speed will be limited to 1G in your network because the ER7206 and TL-SG2210MP both only support 1 Gigabit ports.

Here is the specifications of ER8411 with 2 10G SFP ports: https://www.tp-link.com/en/business-networking/omada-sdn-router/er8411/v1/#specifications

And the 10G switches you may refer to here.

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
2 Reply
Re:Incorporating Omada SDN with existing 10G Hardwares-Solution
2023-10-31 06:43:26 - last edited 2023-11-09 01:41:01

Hello @deo2888,

 

Based on your requirements and descriptions, the 10G speed will be limited to 1G in your network because the ER7206 and TL-SG2210MP both only support 1 Gigabit ports.

Here is the specifications of ER8411 with 2 10G SFP ports: https://www.tp-link.com/en/business-networking/omada-sdn-router/er8411/v1/#specifications

And the 10G switches you may refer to here.

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:Incorporating Omada SDN with existing 10G Hardwares
2023-11-08 08:48:32

  @deo2888 

Hi there! It's great that you're planning to incorporate Omada SDN into your network for the capcut pro video editing company. Your network requirements seem well thought out, and it's always a good idea to seek input from the community for a second opinion. Don't hesitate to share your network topology for more specific advice. Best of luck with your setup!

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 282

Replies: 2

Related Articles