ETH2 2 port on OC200: How to configure

ETH2 2 port on OC200: How to configure

ETH2 2 port on OC200: How to configure
ETH2 2 port on OC200: How to configure
2024-06-11 15:39:52

I am the process of setting up my OMADA System .   I have a blue iris IP cam system.   My plan is as follows:

 

1) ERT707 is Connected to the internet ( VERIZON)

2) It will also be connected to the OC200 controller via SFP port ( Not shown) 

 

3) I want to use the TL-SG3428MP as a dedicated POE switch for my IP cameras

 

4) I also have a second NIC on my blue iris dedicated computer. It isolates the camera from the internet.

 

5) My quesiton is where to connect the 2nd NIC ? I would like to be able to manage it via the cloud controlled but keep it isolated from the internet.

   A)  Do I connect the second NIC via RJ45 to the ETH2 port on the  OC200?

  or B) Can I connect it to any of the ports on the POE router

 

 

OR  is better just to assign the cameras to a VLAN and use ACL to deny the cams access to the internet..

 

Thanks again

     

 

ALl of the IP addresses are 192.168. X. X.

 

 

 

97b24c0c133648f5bb8fb64ba06eb90a

  0      
  0      
#1
Options
4 Reply
Re:ETH2 2 port on OC200: How to configure
2024-06-11 20:02:53

  @lucianp 

 

Access to the net where someone can remotely see it?

 

You dont need to configure it to the cloud access.  You can configure it stand alone.  

I can not teach anyone anything - I can only make them think - Socrates
  0  
  0  
#2
Options
Re:ETH2 2 port on OC200: How to configure
2024-06-11 20:26:43

  @KimcheeGUN 

Thanks I don't need remote access. I just want to be able to see all of the devices on the Omada controller. I just wasn't sure how to deal with the second Nic

 

  0  
  0  
#3
Options
Re:ETH2 2 port on OC200: How to configure
2024-06-11 23:56:34

  @lucianp 

 

In my opinion, you put the vlan on the cctv and isolated the internet by acl. I think it is easier.

  0  
  0  
#4
Options
Re:ETH2 2 port on OC200: How to configure
2024-06-12 05:50:45

Hi  @lucianp 

 

You can connect ETH2 port to the OC200, and put OC200 to a management VLAN. Use ACL to limit the access from other VLANs to the management VLAN:

How to configure Management VLAN in Omada SDN Controller (4.4.4 or above)

 

lucianp wrote

I am the process of setting up my OMADA System .   I have a blue iris IP cam system.   My plan is as follows:

 

1) ERT707 is Connected to the internet ( VERIZON)

2) It will also be connected to the OC200 controller via SFP port ( Not shown) 

 

3) I want to use the TL-SG3428MP as a dedicated POE switch for my IP cameras

 

4) I also have a second NIC on my blue iris dedicated computer. It isolates the camera from the internet.

 

5) My quesiton is where to connect the 2nd NIC ? I would like to be able to manage it via the cloud controlled but keep it isolated from the internet.

   A)  Do I connect the second NIC via RJ45 to the ETH2 port on the  OC200?

  or B) Can I connect it to any of the ports on the POE router

 

 

OR  is better just to assign the cameras to a VLAN and use ACL to deny the cams access to the internet..

 

Thanks again

     

 

ALl of the IP addresses are 192.168. X. X.

 

 

 

 

 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options