Business Community > Gateways > 2.5G WAN/LAN2 is not selectable for load balancing
< Gateways

2.5G WAN/LAN2 is not selectable for load balancing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

2.5G WAN/LAN2 is not selectable for load balancing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
2.5G WAN/LAN2 is not selectable for load balancing
2.5G WAN/LAN2 is not selectable for load balancing
2025-05-16 07:41:33 - last edited 2025-05-19 01:46:09
Model: ER707-M2  
Hardware Version: V1
Firmware Version: 1.2.3 Build 20240822 Rel.52946

I configured the router with three WAN ports:

  • 2.5G WAN1
  • 2.5G WAN/LAN2
  • WAN/LAN3

I would like to balance the load between the two WAN on the ports:

  • 2.5G WAN1
  • 2.5G WAN/LAN2

And use WAN/LAN3 as a backup.

 

The problem is that the the load balancing configuration page does not show 2.5G WAN/LAN2 selectable!

 

Is it a bug or am I doing something wrong!!!?

 

Wan Setting

 

Load Balancing settings

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:2.5G WAN/LAN2 is not selectable for load balancing-Solution
2025-05-16 08:57:51 - last edited 2025-05-19 01:46:09

  @gfrangiamone 

gfrangiamone wrote

  @Clive_A 

 

System Status page shows all three WAN active, WAN Status list shows on 2.5 WAN 1 and WAN/LAN 3

 

1. Reboot it.

2. Try to disable the WAN/LAN2 and re-enable it. This requires two reboots.

3. Do not set the first two WANs in the same subnet. This is incorrect.

Recommended Solution
  1  
  1  
#5
Options
4 Reply
Re:2.5G WAN/LAN2 is not selectable for load balancing
2025-05-16 08:24:29

  @gfrangiamone 

Clear browser cache and try again?

  0  
  0  
#2
Options
Re:2.5G WAN/LAN2 is not selectable for load balancing
2025-05-16 08:31:52
I've tried an anonymous browser window, I've tried restarting the router but nothing changes!
  0  
  0  
#3
Options
Re:2.5G WAN/LAN2 is not selectable for load balancing
2025-05-16 08:43:04

  @Clive_A 

 

System Status page shows all three WAN active, WAN Status list shows on 2.5 WAN 1 and WAN/LAN 3

 

 

 

 

  0  
  0  
#4
Options
Re:2.5G WAN/LAN2 is not selectable for load balancing-Solution
2025-05-16 08:57:51 - last edited 2025-05-19 01:46:09

  @gfrangiamone 

gfrangiamone wrote

  @Clive_A 

 

System Status page shows all three WAN active, WAN Status list shows on 2.5 WAN 1 and WAN/LAN 3

 

1. Reboot it.

2. Try to disable the WAN/LAN2 and re-enable it. This requires two reboots.

3. Do not set the first two WANs in the same subnet. This is incorrect.

Recommended Solution
  1  
  1  
#5
Options

Information

Helpful: 0

Views: 289

Replies: 4

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.