Early Access EAP773 | EAP783 v1.1.1 Pre-release Firmware (Update on 4th Nov, 2025)
This Article Applies to:
EAP783 V1, Fully Adapted to Omada SDN Controller v5.14 or above;
EAP773 V1, Fully Adapted to Omada SDN Controller v5.14 or above;
Release Notes:
New Feature/ Enhancement:
- Supported Portal Logout.
- Supported cluster deployment in Local Controller mode (Omada Central doesn’t support).
- Supported RADIUS Proxy(Global View> Server Settings> Radius Proxy Server).
- Supported OWE.
- Supported upgrading firmware through cloud in standalone mode.
- Supported Rate Limit with Portal Authentication.
- Supported disabling HTTP protocol in Standalone mode.
- Supported DHCP Option43.
- Supported multiple Radius servers when using MAC-Based Authentication (Site View Settings>MAC-Based Authentication).
- Added support for configuring NAS ID with WPA-Enterprise encryption.
- Supported DNS Queries (Network Tools>Network Check>DNSLookup).
- Supported DNS Adoption.
- Supported configuring the Device Name in Controller mode.
- Supported viewing status information and simple configuration through standalone management page when devices managed by the Controller.
- Supported displaying the maximum associated clients range in Controller mode(EAP Config>Advanced>Load Balance).
- Supported displaying the bandwidth of the EAP in Controller mode.
- Added Support for 11 a/n mixed mode for 5GHz radio in Controller mode.
- Supported multicast and broadcast data statistics.
- Supported disabling HTTP, HTTPS and APP discovery in Controller mode (Only with Pro controller).
- Supported Non-stick Roaming function.
- Supported authentication type of EKMS and Generic Radius with Unbound MAC for PPSK with Radius.
- Supports 1024 PPSK entries.
- Supported Multicast Filtering with IPv6 address.
- Supported Multicast/Broadcast Rate Limit
- Supported displaying Configuration Result.
- Optimized roaming function.
- Optimized Automatic Power Optimization function.
- Optimized the configuration of Beacon Interval.
- Optimized Portal Function.
- Optimized MLO connection stability.
- Improved Device and Network security.
- Improved time to configure SSID.
- Improved stability.
Bug Fixed：
- Fixed the issue that RSSI display error in WLAN Optimization.
- Fixed the issue that URL Filtering cannot work properly after TLS1.3 is enabled in the browser.
- Fixed the issue that HTTPS Redirection and Pre-Authentication Access don’t take effect when use portal.
- Fixed the issue that IPv4 multicast packets can’t be transmitted from mesh AP to root AP.
- Fixed the issue that one hop mesh AP’s client on SSID with VLAN would have slow Network speed.
- Fixed the issue that CoA doesn’t take effect with some MLO clients.
Pre-release Firmware Download
Attention
Please be sure you have read the Beta Test Agreement before upgrading the Beta firmware!
EAP783_V1_1.1.1_20251103 (Pre-release)
EAP773_V1_1.1.1_20250818 (Pre-release)
EAP783_V1_1.1.1_20250818 (Pre-release)
Notes:
(1) The above firmware is applied to EAP773&EAP783 V1.
(2) Your device’s configuration won’t be lost after upgrading.
(3) The above firmware is fully adapted to Omada SDN Controller v5.14 and above
Update Log
4th Nov, 2025
Provide the pre-release link for EAP783
EAP783_V1_1.1.1_20251103 (Pre-release)
31th Oct, 2025
Remove the download links.
19th Aug, 2025
Provide the following pre-release link:
EAP773_V1_1.1.1_20250818 (Pre-release)
EAP783_V1_1.1.1_20250818 (Pre-release)
19th Aug, 2025
Update the release note.
Feedback
Any further feedback on the new firmware, please feel free to comment below or start a new thread from HERE.
To get better assistance, you may check Tips For Efficiently Reporting an Issue In The Community.
When reporting an issue, especially it's about firmware upgrade, it's suggested to include the following info:
- Management mode (Controller or Standalone)
- Device Model(s) and Hardware
- Device Firmware (previous and current)
Thank you in advance for your great cooperation and support.
Recommended Threads
Experience the Latest Omada EAP Firmware - Trial Available Here, Subscribe for Updates!
Current Available Solutions to Omada EAP Related Issues [Constantly Updated]
Get the Latest Omada SDN Controller Releases Here - Subscribe for Updates
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi Vincent and everyone,
I’m the one who previously reported that the iPhone 17 Pro could not connect to the EAP783 via MLO.
I’m happy to share that with the new firmware EAP783_V1_1.1.1_20251103 (Pre-release), my iPhone finally connects using MLO without any issue.
To clarify the situation:
A few hours ago, I updated my iPhone to iOS 26.1 as soon as it was released. However, the MLO connection problem with the EAP783 still did not improve after the iOS update alone.
Only after updating the access point to the new pre-release firmware did the iPhone immediately start connecting via MLO successfully. So in my case, the firmware update on the EAP783 side was the key factor for resolving this issue.
This is just my speculation, but since the timing of the iOS update and the new EAP783 firmware release was almost identical, there might have been some compatibility improvements applied on both sides. In any case, with these two updates now in place, MLO is currently working perfectly for me.
Many thanks to the TP-Link team for your continuous support and effort!
- Copy Link
- Report Inappropriate Content
@mrmbman where is this 1.1.3 I cannot find?
- Copy Link
- Report Inappropriate Content
@JIN_JPN is there any note in apple release 26.1 referring to wifi or MLO at all?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
yeah it looks like the release was pulled. If you just google eap783 1.1.3 you will find mentions of it. I'm running it on both my APs.
confused about this new 1.1.1 pre release
and confused why 1.1.3 was pulled
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Yes, we removed version 1.1.3 because that firmware had an issue affecting functionality in specific usage scenarios. This pre-release firmware resolves the problem. Additionally, the new version 1.1.4 will be released very soon. Thank you all for your attention!
- Copy Link
- Report Inappropriate Content
Thank you for the clarification.
- Copy Link
- Report Inappropriate Content
To confirm, there is no way for me to switch to this newer beta from 1.1.3 is there? Since it said no downgrades and this is beta for 1.1.1. (I did try and it failed, but maybe some work around?)
- Copy Link
- Report Inappropriate Content
Hi @mrmbman
Yes.
But the issue in v1.1.3 only triggers under specific configurations.
Are you experiencing any problems currently? If not, I recommend staying on your current config and waiting for the official firmware release.
However, if you’d like to proceed with upgrading to this pre-release version, please let me know.
mrmbman wrote
To confirm, there is no way for me to switch to this newer beta from 1.1.3 is there? Since it said no downgrades and this is beta for 1.1.1. (I did try and it failed, but maybe some work around?)
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 6709
Replies: 67
Voters 0
No one has voted for it yet.