Early Access EAP7xx Fully Adapted to Omada 6.2 Pre-release Firmware (Update on 16th Mar, 2026)
This Article Applies To:
EAP723 V1, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP770 V2, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP772-outdoor V1, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP772 V2, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP787 V1, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP720 V1, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP723 V2, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP725-Wall V1, Fully Adapted to Omada SDN Controller v6.2 or above;
EAP775-Wall V1, Fully Adapted to Omada SDN Controller v6.2 or above;
Note
To update to this pre-release version, please make sure your device version is not lower than the version listed below:
EAP723 V1: 1.3.2 Build 20250901 Rel. 52255
EAP770 V2: 1.3.2 Build 20250901 Rel. 52255
EAP772-outdoor V1: 1.3.2 Build 20250901 Rel. 52255
EAP772 V2: 1.3.2 Build 20250901 Rel. 52255
EAP787 V1: 1.1.2 Build 20251013 Rel. 32717
EAP720 V1: 1.1.2 Build 20250901 Rel. 74897
EAP723 V2: 1.1.2 Build 20250901 Rel. 74897
EAP725-Wall V1: 1.1.2 Build 20250901 Rel. 74897
Release Notes:
New Features
- Added the Omada Config tool for batch configuration of Omada devices.
- Added portal authentication/deauthentication buttons to the client list in the web interface.
- Added CLI commands to support iPerf3 speed tests.
Enhancement
- Optimized device cloud upgrade timeout scenarios, supporting breakpoint resume functionality.
- Optimized AP LAN port status display on the controller.
- Optimized system stability.
- Optimized the client list display on the web interface, adding the guest client list.
Bugs Fixed
- Fixed the issue where the ACL allow list for inter-terminal communication was not effective when guest networks were enabled.
- Fixed topology display anomalies in some scenarios.
- Fixed anomalies in data statistics for certain wired scenarios.
- Fixed the issue where guest clients could not access the portal logout page.
- Fixed the issue where wired terminals still appeared online after being offline for 5 minutes.
- Fixed the issue where PPSK configuration changes did not take effect promptly on controllers earlier than V5.14.
- Fixed some known issues.
Beta Firmware Download
Attention
Please be sure you have read the Beta Test Agreement before upgrading the Beta firmware!
EAP723_v1_1.5.0_20260316-rel11609(pre-release version)
EAP770 _v2_1.5.0_20260316-rel11609(pre-release version)
EAP772-outdoor _v1_1.5.0_20260316-rel11609(pre-release version)
EAP772 _v2_1.5.0_20260316-rel11609(pre-release version)
EAP787 _v1_1.5.0_20260316-rel11609(pre-release version)
EAP720 _v1_1.3.0_20260316-rel6471(pre-release version)
EAP723 _v2_1.3.0_20260316-rel6471(pre-release version)
EAP725-Wall_v1_1.3.0_20260316-rel6471(pre-release version)
EAP775-Wall_v1_1.3.0_20260316-rel11609(pre-release version)
EAP723_v1_1.5.0_20260121-rel65599(pre-release version)
EAP770 _v2_1.5.0_20260121-rel65599(pre-release version)
EAP772-outdoor _v1_1.5.0_20260121-rel65599(pre-release version)
EAP772 _v2_1.5.0_20260121-rel65599(pre-release version)
EAP787 _v1_1.5.0_20260121-rel65599(pre-release version)
EAP720 _v1_1.3.0_20260121-rel65599(pre-release version)
EAP723 _v2_1.3.0_20260121-rel65599(pre-release version)
EAP725-outdoor_v1_1.3.0_20260121-rel65599(pre-release version)
EAP725-Wall_v1_1.3.0_20260121-rel65599(pre-release version)
Notes:
(1) Your device’s configuration won’t be lost after upgrading.
(2) The above firmware is fully adapted to Omada SDN Controller v6.2 and above.
(3) This pre-release firmware can be applied to all versions (EU/US/AU/CA/etc).
Update Log
16th Mar, 2026
Update the pre-release link to the following:
EAP723_v1_1.5.0_20260316-rel11609(pre-release version)
EAP770 _v2_1.5.0_20260316-rel11609(pre-release version)
EAP772-outdoor _v1_1.5.0_20260316-rel11609(pre-release version)
EAP772 _v2_1.5.0_20260316-rel11609(pre-release version)
EAP787 _v1_1.5.0_20260316-rel11609(pre-release version)
EAP720 _v1_1.3.0_20260316-rel6471(pre-release version)
EAP723 _v2_1.3.0_20260316-rel6471(pre-release version)
EAP725-Wall_v1_1.3.0_20260316-rel6471(pre-release version)
EAP775-Wall_v1_1.3.0_20260316-rel11609(pre-release version)
Update Note:
Fixed some known bugs.
30th Jan, 2026
Remove the download link of EAP725-outdoor.
23rd Jan, 2026
Provide the pre-release link:
EAP723_v1_1.5.0_20260121-rel65599(pre-release version)
EAP770 _v2_1.5.0_20260121-rel65599(pre-release version)
EAP772-outdoor _v1_1.5.0_20260121-rel65599(pre-release version)
EAP772 _v2_1.5.0_20260121-rel65599(pre-release version)
EAP787 _v1_1.5.0_20260121-rel65599(pre-release version)
EAP720 _v1_1.3.0_20260121-rel65599(pre-release version)
EAP723 _v2_1.3.0_20260121-rel65599(pre-release version)
EAP725-outdoor_v1_1.3.0_20260121-rel65599(pre-release version)
EAP725-Wall_v1_1.3.0_20260121-rel65599(pre-release version)
Feedback
Any further feedback on the new firmware, please feel free to comment below or start a new thread from HERE.
To get better assistance, you may check Tips For Efficiently Reporting an Issue In The Community.
When reporting an issue, especially it's about a firmware upgrade, it's suggested to include the following info:
- Management mode (Controller or Standalone)
- Device Model(s) and Hardware
- Device Firmware (previous and current)
Thank you in advance for your great cooperation and support.
Recommended Threads
Experience the Latest Omada EAP Firmware - Trial Available Here, Subscribe for Updates!
Current Available Solutions to Omada EAP Related Issues [Constantly Updated]
Get the Latest Omada SDN Controller Releases Here - Subscribe for Updates
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @MiLK_MaN
Thank you so much for taking the time to post the issue on the TP-Link community!
To better assist you, I've created a support ticket via your registered email address and escalated it to our support engineer to look into the issue. The ticket ID is TKID260218705. Please check your inbox and confirm that the support email was received. Thanks!
Once the issue is resolved, please update this thread with your solution to help others who may encounter the same problem.
Many thanks for your excellent cooperation and patience!
- Copy Link
- Report Inappropriate Content
@Vincent-TP
I'm running this on one of my networks with 3 AP's, two times the EAP723 V2 and an EAP725-Wall V1. Cannot get a single client to use the EAP725-Wall V1 IF it's a client that has the option to pick 5GHz. 2.4 clients utilize the AP, every 5g client ignores the EAP725-Wall V1 and fails to connect .... debugged one of the clients to not receive any network information.
So far, I've tried a reconfiguration and a reset, and I've made sure the bands are compatible with the clients. These clients have no issues with the 723's.
Any suggestions to debug?
- Copy Link
- Report Inappropriate Content
@Vincent-TP Hi
My EAP 720 V1 US running on 1.2.0 FW not taking the 1.3.0 FW update. giving error Cannot upgrade the firmware of this model. It has been configured with a target firmware version on this site.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Just to keep things clean. My issue has been resolved and was totally unrelated to the firmware. I started downgrading and found the same issue and then noticed I made a booboo configuring the uplink port for the AP, it was running infra vlan by default by block all others. Still very strange to be honest that 2.4ghz then kinda works for some devices, but 5ghz totally not. Nevertheless resolved.
- Copy Link
- Report Inappropriate Content
Hi @doeLauw
Thanks for taking the time to share the reason with us. Any new inquiries in the future, don't hesitate to let us know.
doeLauw wrote
Just to keep things clean. My issue has been resolved and was totally unrelated to the firmware. I started downgrading and found the same issue and then noticed I made a booboo configuring the uplink port for the AP, it was running infra vlan by default by block all others. Still very strange to be honest that 2.4ghz then kinda works for some devices, but 5ghz totally not. Nevertheless resolved.
- Copy Link
- Report Inappropriate Content
Hi @Vishlamba
Thanks for posting here.
To better understand the situation, please share a screenshot of the error message page.
Where did you get the 1.2.0 version?
It has been configured with a target firmware version on this site.
>>>What does this mean? please share a screenshot of the mentioned config page. Thanks.
Vishlamba wrote
@Vincent-TP Hi
My EAP 720 V1 US running on 1.2.0 FW not taking the 1.3.0 FW update. giving error Cannot upgrade the firmware of this model. It has been configured with a target firmware version on this site.
- Copy Link
- Report Inappropriate Content
Hi PFA the Screen shot as requested. Also FW 1.2.0 Build 20260116 Rel. 73786 was from the 6th Feb 2026 update. Please see the screen shot for the same. I tried updating to the new build available for 1.2.0 20260130 also, but getting the same error seccren shot for the same attached. Thanks
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 4685
Replies: 29
Voters 0
No one has voted for it yet.