Eap110

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Eap110

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Eap110
Eap110
2017-09-27 23:00:11
Model :

Hardware Version :

Firmware Version :

ISP :

Hi All

Not sure on which version i have V1 or V2 (not sure how to find out)

My only question is how many connected clients/device can i get on 1 SSID (if i create multiple SSIDs will that reduce the total connected devices across all or will i get for example 50 connections live on each SSID?
  0      
  0      
#1
Options
4 Reply
Re:Eap110
2017-09-28 14:54:29

MarcChamberlain wrote

Not sure on which version i have V1 or V2 (not sure how to find out)

Please check the backside of EAP110, you will see a serial number and next to it you will see ver1.0/2.0 or EU1.0/2.0
ver 1.0 and EU 1.0 mean V1.


My only question is how many connected clients/device can i get on 1 SSID (if i create multiple SSIDs will that reduce the total connected devices across all or will i get for example 50 connections live on each SSID?

According to TP-Link support, the recommended connection is 30 in total, no matter how many ssids you set up( no more than 8 SSIDs),
  0  
  0  
#2
Options
Re:Eap110
2017-09-28 15:45:36
Strongly depends on environment, AirTIme and the usage pattern. For example, if users are streaming 720p videos, it will work smoothly for up to 20-25 clients in 2.4 GHz band if enough AirTIme is available. If the user's data volume is rather low, 30-40 clients could use the EAP110.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#3
Options
Re:Eap110
2017-09-28 16:36:16
So i have managed to confirm we are using V2

The environment we are in or do is below

Our company tests phones via a software thats installed on a PC and also the phone, more of a Quality Check (QC) - in order to test the phones we have to connect them to a wifi until the test is complete - this can take about 5 minutes per device but we have for example 10 staff with 6 devices each all running at the same time. once the device has established wifi connection and completed the test we rest the device to factory reset which will also at the time release the IP from the device.

We have and are currently using things more expensive like Cisco APs (Aironet 3700/2600) but noticed that we can connect several phones up but the release time seems to be a delay on the AP and (loses its IP) it takes a few minutes for those block of IP address to become available again so the next batch of devices can see and pick them up
  0  
  0  
#4
Options
Re:Eap110
2017-09-29 18:11:29

MarcChamberlain wrote


We have and are currently using things more expensive like Cisco APs (Aironet 3700/2600) but noticed that we can connect several phones up but the release time seems to be a delay on the AP and (loses its IP) it takes a few minutes for those block of IP address to become available again so the next batch of devices can see and pick them up


That's an effect caused by the DHCP server, not the WiFi AP. You should reduce the DHCP lease time so that unused leases will be re-useable instantly.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 963

Replies: 4

Related Articles