Business Community > All Threads > CPE210 V1.1 Australia drops out often
< All Threads

CPE210 V1.1 Australia drops out often

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE210 V1.1 Australia drops out often

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE210 V1.1 Australia drops out often
CPE210 V1.1 Australia drops out often
2018-04-03 09:54:21
Model : CPE210

Hardware Version :

Firmware Version : 1.3.0 Build 20150612 Rel. 50957

ISP : iiNet

I have got 2 Ubiquiti Nanostation M's connecting from in town to a building at the back of the property, and then 2 CPE210's connecting it to the house <100m away. But the internet connection constantly drops out for up to 2 minutes at a time, then comes back on its own.

The one that is transmitting is set to access point mode, and the other is set to client mode.
I have the transmit power set to 11dBm, the distance is 0.1km, and it is set to have a static IP.
Firmware Version: 1.3.0 Build 20150612 Rel. 50957

Should I set it to DHCP?
I think the distance may be a bit less than 0.1km, could that affect it?
  0      
 
  0      
 
#1
Options
6 Reply
Re:CPE210 V1.1 Australia drops out often
2018-04-03 19:58:46

cpe210Broke wrote


Firmware Version: 1.3.0 Build 20150612 Rel. 50957


That's a quite old version, update to latest firmware (2.1.12). Note that CPE210 HW v1.x uses standard Pharos firmware (same files as for CPE510 and WBS210/510), while CPE210 HW v2+ uses a different firmware version.

Should I set it to DHCP?
I think the distance may be a bit less than 0.1km, could that affect it?


No, static IP is fine. Ensure they have different, unique IPs. Distance of 100m also is no problem, but set TX power to maximum, wireless mode to 802.11n, short GI enabled, WMM enabled, channel bandwidth 20MHz. Also make sure you ground the devices properly (see the installation guide) and adjust antennas of both devices carefully (status page will help you doing so).
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:CPE210 V1.1 Australia drops out often
2018-04-04 13:03:07
Thanks, I'll try those things out and get back to you It doesn't appear to have a ground cable and from what I can tell we didn't use shielded Ethernet cables. Would that be causing the dropouts? Even when there is no storm? A while ago our power went out during a storm, and when it came back up the Cpe210 was reset and I had to configure it again. Is that due to it not being grounded.
  0  
  0  
#3
Options
Re:CPE210 V1.1 Australia drops out often
2018-04-04 13:31:10
Here are the signal strengths attached
File:
152281976311048004448.jpgDownload
  0  
  0  
#4
Options
Re:CPE210 V1.1 Australia drops out often
2018-04-05 02:21:43
Signal strength is o.k., but could be better on such a short distance. Try to align the CPE's front exactly to each other. You should also upgrade the firmware to 2.1.12. Download it from the german TP-Link website (tp-link.de), you can find the Pharos 2.1.12 firmware on their WBS510 support page. Albeit it's marked for V2 devices only, it installs on CPE210 v1.1, too.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#5
Options
Re:CPE210 V1.1 Australia drops out often
2018-04-05 11:51:07
Before you sent that I had already installed v2.1.6 from the Australian cp210 page. Is that one fine?
  0  
  0  
#6
Options
Re:CPE210 V1.1 Australia drops out often
2018-04-08 21:18:14

cpe210Broke wrote

Before you sent that I had already installed v2.1.6 from the Australian cp210 page. Is that one fine?


I had no problems with v2.1.6, but given the fact that 2.1.11 and 2.1.12 were released shortly thereafter, changes are that bugs have been fixed since 2.1.6.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1256

Replies: 6

Related Articles
TP-link CPE210 V1.1
2676 0
CPE210 v1.1 (with test mode) firmware
1529 0
What is the difference between the CPE210 v1.0 and the new v1.1?
3297 0
WHAT IS THE RIGHT FIRMWARE UPGRADE FOR CPE210 v1.1?
641 0
CPE 210 V1.1 Firmware Restore
3585 0
CPE210 V1.1 How to limit access to certain IP range?
1041 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.