Home

Forums

Stories

Knowledge Base

Business Community > All Threads > T1600G-28TS multii VLAN on 1 port

< All Threads

T1600G-28TS multii VLAN on 1 port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

T1600G-28TS multii VLAN on 1 port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

xcSTRIKER

2020-08-31 14:31:53 - last edited 2020-09-03 12:01:14

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-08-26

T1600G-28TS multii VLAN on 1 port

2020-08-31 14:31:53 - last edited 2020-09-03 12:01:14

Model: T1600G-28TS(TL-SG2424)

Hardware Version: V2

Firmware Version:

Hello,

I have read multiple threads but perhaps I have missed the one where I setup up multiple VLAN's on a single physical port.

How do I configure a physical port on the T1600G-28TS.

Port 1 --> Router (Configured for VLAN default & VLAN ID 5)

Port 2 --> AP (VLAN Default & VLAN ID 5)

If I connect the AP directly into the same router port the switch was copnnected to the VLANs work with no problem. So it is my Switch that is not passing the VLAN traffic correclty. I just do not see how I can configure mutliple VLANs on a single physical port on this switch.

What is the difference between 802.1Q VLAN & Protocol VLAN. Am i supposed to use Protocal VLAN for multiple LVAN on a single port?

Thanks

1 Accepted Solution

Fae

2020-09-01 06:57:11 - last edited 2020-09-03 12:01:14

Posts: 3604

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:T1600G-28TS multii VLAN on 1 port-Solution

2020-09-01 06:57:11 - last edited 2020-09-03 12:01:14

Dear @xcSTRIKER,

What is the difference between 802.1Q VLAN & Protocol VLAN. Am i supposed to use Protocal VLAN for multiple LVAN on a single port?

802.1Q VLAN is the port-based VLAN technology, while the Protocol VLAN is Protocol-based VLAN technology.

Protocol VLAN uses the protocol to determine one device belongs to which specific VLAN.

How do I configure a physical port on the T1600G-28TS.

Port 1 --> Router (Configured for VLAN default & VLAN ID 5)

Port 2 --> AP (VLAN Default & VLAN ID 5)

I just do not see how I can configure mutliple VLANs on a single physical port on this switch.

On the T1600 switch, create VLAN 5 and select both Port1 and Port2 as Tagged Port, the port on the router should be tagged as well in VLAN 5. As for the default VLAN 1, you could leave it as default parameters.

Hope this information is helpful.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

2 Reply

Fae

2020-09-01 06:57:11 - last edited 2020-09-03 12:01:14

Posts: 3604

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:T1600G-28TS multii VLAN on 1 port-Solution

2020-09-01 06:57:11 - last edited 2020-09-03 12:01:14

Dear @xcSTRIKER,

What is the difference between 802.1Q VLAN & Protocol VLAN. Am i supposed to use Protocal VLAN for multiple LVAN on a single port?

802.1Q VLAN is the port-based VLAN technology, while the Protocol VLAN is Protocol-based VLAN technology.

Protocol VLAN uses the protocol to determine one device belongs to which specific VLAN.

How do I configure a physical port on the T1600G-28TS.

Port 1 --> Router (Configured for VLAN default & VLAN ID 5)

Port 2 --> AP (VLAN Default & VLAN ID 5)

I just do not see how I can configure mutliple VLANs on a single physical port on this switch.

Hope this information is helpful.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Information

Helpful: 0

Replies: 2

T1600G-28TS multii VLAN on 1 port

T1600G-28TS multii VLAN on 1 port

Information

Voters 0

Tags