Business Community > All Threads > T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active
< All Threads

T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active
T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active
2020-09-05 21:48:05 - last edited 2020-09-16 09:30:48
Model: T1500G-10MPS  
Hardware Version: V2
Firmware Version: 2.0.5 Build 20200109 Rel.37690(s)

Just received my new T1500G-10MPS in which I hooked my OC200 up to and powered it up fine (shows 100mbs on the port which is should). Connected POE camera and works great (again shows 100mbs which it should). However when I hook one of my EAP225-Outdoor POEs up , the switch powers the unit but does not display as the port being active which in turn the AP connects to one of my other APs via mesh instead of independently.

 

 

As you can see for Port 3 - notta ziltch- but you can see in the image below it is powering the AP?

 

I have ran a new Cat6 cable 3 times to this AP which is only 25 feet away from the Switch's location. So I am at a lost unless there is something I am missing. Yes, I also updated the firmware to the latest version. Just a bit mind blown by this issue since the AP works perfectly fine with a POE injector. Actually the AP is working but with MESH not independantly as I want it to.

 

Any help with this would be great!

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active-Solution
2020-09-07 00:38:42 - last edited 2020-09-16 09:30:48

Disregard, issue has been resolved. Had a fault in the power wiring where the switch was plugged up at. Repaired and working fine.

Recommended Solution
  1  
  1  
#2
Options
Re:T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active-Solution
2020-09-07 14:17:38 - last edited 2020-09-16 09:30:52

@Yannie 

 

Honestly I don't think I would have found it if it was not for my UPS backup alerting me of a fault in the outlet. 

 

Once I replaced the outlet and secured the electrical wires thats when I noticed the switch started to perform as it should.

 

My farm house is much older , being built in 1958 so there is still some (a couple of outlets) odd wiring that exist. Someone replaced this outlet before with a ground fault outlet but it was not property wired.

 

Do the TP-Link switches have a ground fault or power regulator notification built-in? If not that may be something to consider having added in future products.

Recommended Solution
  1  
  1  
#4
Options
4 Reply
Re:T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active-Solution
2020-09-07 00:38:42 - last edited 2020-09-16 09:30:48

Disregard, issue has been resolved. Had a fault in the power wiring where the switch was plugged up at. Repaired and working fine.

Recommended Solution
  1  
  1  
#2
Options
Re:T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active
2020-09-07 06:27:57

@Reconboy 

 

Interesting, but how you can find it's the power wiring issue? It enlightens me that we also need to consider the problem from the power source including the power outlet and power wiring when it's related to power. Thanks!

  0  
  0  
#3
Options
Re:T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active-Solution
2020-09-07 14:17:38 - last edited 2020-09-16 09:30:52

@Yannie 

 

Honestly I don't think I would have found it if it was not for my UPS backup alerting me of a fault in the outlet. 

 

Once I replaced the outlet and secured the electrical wires thats when I noticed the switch started to perform as it should.

 

My farm house is much older , being built in 1958 so there is still some (a couple of outlets) odd wiring that exist. Someone replaced this outlet before with a ground fault outlet but it was not property wired.

 

Do the TP-Link switches have a ground fault or power regulator notification built-in? If not that may be something to consider having added in future products.

Recommended Solution
  1  
  1  
#4
Options
Re:T1500G-10MPS powers EAP225-Outdoor AP but does not show the port as being active
2020-09-08 02:06:17

Dear @Reconboy,

 

Do the TP-Link switches have a ground fault or power regulator notification built-in? If not that may be something to consider having added in future products.

 

Thank you for the suggestion. I've written it down which will be forwarded to our developers for consideration. Thank you again for your feedback.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1412

Replies: 4

Related Articles
T1500G-10MPS - Cannot handle more than 9 devices
1140 0
T1500G-10MPS firmware
2133 1
T1500G-10MPS(UN) Ver 2.0
575 0
Activate POE on T1500G-10MPS
862 0
T1500-G-10mps suddently down
668 0
EAP225 outdoor--resetting an individual AP
954 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.