Business Community > All Threads > Port Forwarding/ Virtual Server Omada Controller
< All Threads

Port Forwarding/ Virtual Server Omada Controller

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Port Forwarding/ Virtual Server Omada Controller

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Port Forwarding/ Virtual Server Omada Controller
Port Forwarding/ Virtual Server Omada Controller
2021-01-12 00:38:33 - last edited 2022-08-11 12:42:10
Tags: #Port Forwarding
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version:

Hi,

 

I have been slowly adding to my Omada set-up and just installed my last piece the TL-R605 gateway to go with a couple managed switches and EAPs in my home network.  Everything has been pretty easy to get set-up and working.  The only thing I can't figure out is the port forwarding within the controller software.  It looks different than what I am used to and when I look up in the user manual the screen shots it shows are different (I assume they are showing logging directly into the gateway versus using Omada controller).  The way the user guide shows is what I would expect but in Omada software it asks for a destination IP address as well and not sure what to use.  I can't find an example for setting up within the Omada software online.  Any help would be appreciated.

 

Thanks,

 

 

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Port Forwarding/ Virtual Server Omada Controller-Solution
2021-01-12 09:07:55 - last edited 2022-08-11 12:42:21

Dear @TheWookie,

 

The way the user guide shows is what I would expect but in Omada software it asks for a destination IP address as well and not sure what to use.

 

 

Please check Page 107 from the UG of the Omada Controller below.

https://static.tp-link.com/2020/202012/20201223/1910012926-Omada%20SDN%20Controller%204.2.4-User%20Guide.pdf

 

For Omada Controller, please go to Setting > Transmission > NAT > Port Forwarding to configure the parameters.

 

Here is a configuration example for your reference. https://www.tp-link.com/support/faq/2132/

Note: the web UI is different, but the configuration steps for port forwarding are similar.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
Re:Port Forwarding/ Virtual Server Omada Controller-Solution
2021-01-12 13:54:02 - last edited 2021-01-13 00:50:49

@TheWookie 

 

I think what you are looking for is as the following image - 

 

Hopefully this will help you - the destination IP address should be the IP of which the service device is running on - This is just a quick setup I did to show an example

 

Recommended Solution
  6  
  6  
#4
Options
4 Reply
Re:Port Forwarding/ Virtual Server Omada Controller-Solution
2021-01-12 09:07:55 - last edited 2022-08-11 12:42:21

Dear @TheWookie,

 

The way the user guide shows is what I would expect but in Omada software it asks for a destination IP address as well and not sure what to use.

 

 

Please check Page 107 from the UG of the Omada Controller below.

https://static.tp-link.com/2020/202012/20201223/1910012926-Omada%20SDN%20Controller%204.2.4-User%20Guide.pdf

 

For Omada Controller, please go to Setting > Transmission > NAT > Port Forwarding to configure the parameters.

 

Here is a configuration example for your reference. https://www.tp-link.com/support/faq/2132/

Note: the web UI is different, but the configuration steps for port forwarding are similar.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
Re:Port Forwarding/ Virtual Server Omada Controller
2021-01-12 13:37:35 - last edited 2021-01-12 13:41:45

@Fae 

 

Thanks for the reply.  I think what I am getting hung up on is in the new UI for Omada 4.2.8 there is an additional required box which is the destination IP address that I can't leave blank and that wasn't in the example provided or in other routers I have used.  What I am trying to figure out is what should I put in there?  Neither the LAN (of router)/ WAN addresses seem to be the right one so I am missing something that I am not understanding from the manual or the example.  That seems to really be the only difference from my previous set-up.

 

Thanks,

  0  
  0  
#3
Options
Re:Port Forwarding/ Virtual Server Omada Controller-Solution
2021-01-12 13:54:02 - last edited 2021-01-13 00:50:49

@TheWookie 

 

I think what you are looking for is as the following image - 

 

Hopefully this will help you - the destination IP address should be the IP of which the service device is running on - This is just a quick setup I did to show an example

 

Recommended Solution
  6  
  6  
#4
Options
Re:Port Forwarding/ Virtual Server Omada Controller
2021-01-12 14:07:41

@Reconboy 

 

Thanks, this just triggered me to realize that I was thinking about this backwards!  Got it working now, thank you!

  1  
  1  
#5
Options

Information

Helpful: 0

Views: 37579

Replies: 4

Tags

Port Forwarding
Related Articles
Unable to get port forwarding (virtual server) to work on ER605
3036 0
Virtual Servers / Port Forwarding from OpenVPN Tunnel
640 2
Omada Controller - can't delete port forwardin (only disable) Transmission-NAT-Port Forwarding
908 0
Omada Controller Port Forwarding
6163 1
Max Virtual Server
654 0
omada port forwarding
961 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.