TL-R605 SNMP interface statistics

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-R605 SNMP interface statistics

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-R605 SNMP interface statistics
TL-R605 SNMP interface statistics
2021-01-18 10:37:48
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version: 1.0.0 Build 20200930 Rel.36519

Hi

 

Trying to use SNMP on my TL-R605 router to get some internet usage statistics, however it doesn't seem to be reporting quite correctly (or I'm looking at the wrong thing!)

Looking at the interface descriptions, I can't really tell which one is wan or lan, but MAC addresses suggests .9 is wan (veth1), and .11 is lan (eth0.1)

 

 

Looking at the in/outOctets seems like the obvious place to start, however these counts don't seem to change with internet use (ie downloading a 1gb test file does not increase count by 1gb!)

 

 

 

Looking at the same base OID (1.3.6.1.2.1.2.2.1.10.49153) on my SG2428P for the port which is connected to the R605 I can get more accurate measurements (ie download 1gb file, count increases by 1gb!)

 

 

Anyone know if I'm just looking at the wrong thing on the router, or are the counts not accurate at the moment?

 

Thanks

  2      
  2      
#1
Options
9 Reply
Re:TL-R605 SNMP interface statistics
2021-02-28 16:23:10

@cosmo0000 

 

hey, did you ever figure this out?

im having the same problem. 
 

also the stats in the standalone gui look wrong too

  0  
  0  
#2
Options
Re:TL-R605 SNMP interface statistics
2021-03-01 17:48:59

Is nobody else suffering at the hands of this duff firmware?

  0  
  0  
#3
Options
Re:TL-R605 SNMP interface statistics
2021-03-01 17:56:58
I've noted that the data transfer reported by the controller tends not to match up with what I expect to see. It's frustrating because I'm not confident I'm getting full use of my three WAN links, but am not able to debug much without accurate stats. I'm not sure how much of this is fundamental, and how much is some weird artifact of the 5-minute resolution of SDN's graphs.
  0  
  0  
#4
Options
Re:TL-R605 SNMP interface statistics
2021-03-03 22:03:28

@sam_r 

 

v1.0.1 firmware for TL-R605 doesn't fix this.

  0  
  0  
#5
Options
Re:TL-R605 SNMP interface statistics
2021-05-23 18:49:00

I'd be curious if there has been any development on this. I have been trying to get the SNMP data to pull into HomeAssistant but nothing seems to really match up.

  0  
  0  
#6
Options
Re:TL-R605 SNMP interface statistics
2021-05-26 08:33:21

@cosmo0000 

 

I'm not actually using the R605 right now, but it' still connected to my network.

I do see the interfaces via SNMP:

 

 

And I do get a bit of traffic on the "internal" one, too:

 

 

 

I can't tell you if the stats are correct. But in general, TP-Link sticks to the protocol and uses the right OIDs.

  0  
  0  
#7
Options
Re:TL-R605 SNMP interface statistics
2021-05-26 11:24:50

@SaschaG 

hi everyone,

i also have the same problem with the tl-r605.

have any of you solved?

technical support does not have the MIB file

  0  
  0  
#8
Options
Re:TL-R605 SNMP interface statistics
2021-08-06 03:13:39

Hi all, I'm wondering if there's an update to this? 

  0  
  0  
#9
Options
Re:TL-R605 SNMP interface statistics
2022-02-04 14:49:56
Hello what is the read and write community of this device? Thanks?
  0  
  0  
#10
Options

Information

Helpful: 2

Views: 3315

Replies: 9

Related Articles