EAP225 Mesh

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP225 Mesh

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP225 Mesh
EAP225 Mesh
2021-07-13 20:43:26 - last edited 2021-07-14 10:49:15
Model: EAP225-Wall  
Hardware Version: V2
Firmware Version: 5.0.2 Build 20210316 Rel. 67337

Hello,

 

From what I can tell from the datasheet I should be able to setup and create a mesh network with these AP's.  I have mesh enabled in my controller and my AP's adopted and connected.  Here are the details:

 

Model:

EAP225-Wall(US) v2.0

 

Firmware Version:

5.0.2 Build 20210316 Rel. 67337

 

Controller Version:

4.3.5

Model:

OC300 1.0

Firmware Version:

1.1.0 Build 20210406 Rel.58776

 

 

Do I need a different firmware to do this?  If not then what do I need to do?

 

 

Thanks,

 

Stephen

 

 

 

 

  0      
  0      
#1
Options
1 Accepted Solution
Re:EAP225 Mesh-Solution
2021-07-14 01:52:00 - last edited 2021-07-14 10:49:15

@Stephen2021 

 

Agree with @Philbert . EAP's mesh function is to help us deploy EAPs wirelessly. While wall edition of APs usually don't have POE injectors for power supply, that is, you have to use a cable to connect the wall AP to a POE switch to get power over Ethernet. In this case, mesh makes no sense to wall edition.

 

But I think you should distinguish mesh and fast roaming, which I think you actually need ( I also mixed them before lol)

Recommended Solution
  3  
  3  
#3
Options
6 Reply
Re:EAP225 Mesh
2021-07-14 00:31:44

@Stephen2021 

 

Hey

 

I may be incorrect in saying this as I haven't personally tested it, but fairly sure the WALL edition of APs do not support Mesh, simply by design.  Wall editions are designed for a single room in a hotel, or a dormitory and therefore do not have certain features that the standard APs do.  One of these is Fast Roaming and I'm pretty sure Mesh is another.   Being a wall mounted AP its expected this is cabled in some way.

 

The EAP225 245 and 265  standard ceiling mounted APs all support the Mesh feature.  

 

  1  
  1  
#2
Options
Re:EAP225 Mesh-Solution
2021-07-14 01:52:00 - last edited 2021-07-14 10:49:15

@Stephen2021 

 

Agree with @Philbert . EAP's mesh function is to help us deploy EAPs wirelessly. While wall edition of APs usually don't have POE injectors for power supply, that is, you have to use a cable to connect the wall AP to a POE switch to get power over Ethernet. In this case, mesh makes no sense to wall edition.

 

But I think you should distinguish mesh and fast roaming, which I think you actually need ( I also mixed them before lol)

Recommended Solution
  3  
  3  
#3
Options
Re:EAP225 Mesh
2021-07-14 10:53:00

@Stephen2021 

 

Thanks for the replies.   It looks like I was a little confused as well.  Fast Roaming was actually what I was in need of.   This option is disabled by default and under Advanced Features.

 

Stephen

  0  
  0  
#4
Options
Re:EAP225 Mesh
2021-07-15 07:25:55 - last edited 2021-07-15 07:28:34

@Stephen2021 

Wall editions don't support fast roaming either. Even if you enable this feature, I think it won't take effect on wall AP.

  0  
  0  
#5
Options
Re:EAP225 Mesh
2021-07-15 10:18:17

@Somnus 

 

Hi Somnus,

 

Roaming does seem to be working for me though:

 

  0  
  0  
#6
Options
Re:EAP225 Mesh
2021-07-16 08:12:19

@Stephen2021 

 

Hey

 

Its likely that Roaming is working, however Fast and Seamless roaming isn't due to support

 

The controller will try to roam you if enabled and it feels it can do so, however the wall editions don't support seamless roaming and therefore the connection will likely be reset / dropped during the AP handover.   This may not be an issue for you unless you are on a VPN or require the seamless handover.

  1  
  1  
#7
Options

Information

Helpful: 0

Views: 1007

Replies: 6

Related Articles