Business Community > All Threads > EAP615: No PoE Output
< All Threads

EAP615: No PoE Output

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP615: No PoE Output

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP615: No PoE Output
EAP615: No PoE Output
2023-12-04 13:59:13 - last edited 2023-12-04 20:20:01
Tags: #Network Connectivity #PoE
Model: EAP615-Wall  
Hardware Version: V1
Firmware Version: 1.1.6

I wanted to use the PoE-output of my EAP615-Wall and was surprised by the fact, that it didn't work. The product page mentions, that PoE-passthrough is available, if the AP is connected to a PoE 802.3af/802.3at capable switch. I have this switch, which is 802.3af/802.3at compatible: https://www.tp-link.com/business-networking/unmanaged-switch/tl-sg1008p/

 

Is there any setting I forgot? I didn't see anything related to PoE-passthrough. If I connect my PoE device directly to the network-cable where the AP is normally plugged in, my device boots. But as soon as I daisy-chain it after the AP, nothing happens at all.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:EAP615: No PoE Output-Solution
2023-12-04 19:33:06 - last edited 2023-12-04 20:20:01

  @tim-hilt 

 

Click on the radio in the device list within the omada controller.

goto config>advance> and its below.

 

I can not teach anyone anything - I can only make them think - Socrates
Recommended Solution
  1  
  1  
#6
Options
6 Reply
Re:EAP615: No PoE Output
2023-12-04 15:22:06

  @tim-hilt 

 

If you're using the controller/standalone mode, you have to enable the POE passthrough in the controller or GUI.  

 

Be careful on what youre powering... It pulls 11watts with POE off... Do the math to make sure the daisy chained device doesnt pull more then 14-15 watts.  Total cant go past 25 watts.  

I can not teach anyone anything - I can only make them think - Socrates
  1  
  1  
#2
Options
Re:EAP615: No PoE Output
2023-12-04 15:22:51

  @tim-hilt 

 

Also - if the device pulls too much power... the AP and daisy chain device will go into a boot loop.  

I can not teach anyone anything - I can only make them think - Socrates
  1  
  1  
#3
Options
Re:EAP615: No PoE Output
2023-12-04 15:27:11

  @KimcheeGUN ah, that makes sense. I didn't see the setting in the Omada controller, but maybe I can see them, when I go to the ip address of the AP?

 

I can't imagine that the device I'm connecting draws more than 1 or 2 watts, so that shouldn't be the problem. (I didn't measure it though)

KimcheeGUN wrote

  @tim-hilt 

 

If you're using the controller/standalone mode, you have to enable the POE passthrough in the controller or GUI.  

 

Be careful on what youre powering... It pulls 11watts with POE off... Do the math to make sure the daisy chained device doesnt pull more then 14-15 watts.  Total cant go past 25 watts.  

 

  0  
  0  
#4
Options
Re:EAP615: No PoE Output
2023-12-04 15:28:19
Can you tell me where exactly I should look for enabling the poe passthrough?
  0  
  0  
#5
Options
Re:EAP615: No PoE Output-Solution
2023-12-04 19:33:06 - last edited 2023-12-04 20:20:01

  @tim-hilt 

 

Click on the radio in the device list within the omada controller.

goto config>advance> and its below.

 

I can not teach anyone anything - I can only make them think - Socrates
Recommended Solution
  1  
  1  
#6
Options
Re:EAP615: No PoE Output
2023-12-04 20:19:56

  @KimcheeGUN Perfect! Works as expected. Thank you!!!

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 952

Replies: 6

Tags

Network Connectivity
PoE
Related Articles
power EAP615-Wall via PoE injector
66 0
Configuring EAP615-Wall
237 0
EAP615-Wall ethernet ports not working
837 0
POE camera not working when connected to POE passthrough port on EAP615-Wall(US) v1.0
567 0
EAP615-Wall: mixed wired and wireless backhaul
1055 0
EAP615 in series
2183 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.