Port forwarding issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Port forwarding issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Port forwarding issue
Port forwarding issue
2024-01-07 03:00:24 - last edited 2024-01-10 05:32:30
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.2.3 Build 20231201 Rel.32918

I am trying to replace an archer a7 with this er605 and am having an issue forwarding all the port on the network. I have spent hours searching these forums and google and nothing I do is working. I have gone to transmission>Nat> virtual server and filled out the standard  required information like I have done many times in the last decade. I cannot detect any open ports. The previous router port forwarding was working so I am confident the pc firewalls are ok. I read also that the router ACL needed to be set to allow the virtual server through. I think that I have set this correctly, but this is a new step in my experiance in setting up PF. What am I doing wrong or is this just the router having issues?

  0      
  0      
#1
Options
1 Accepted Solution
Re:Port forwarding issue-Solution
2024-01-10 02:42:27 - last edited 2024-01-10 05:32:30

  @d0ugmac1 
The issue was a filtering device called Bark. Once I turned it off forwarding acted like it should. Thanks for your insites.

Recommended Solution
  1  
  1  
#14
Options
13 Reply
Re:Port forwarding issue
2024-01-07 14:02:37 - last edited 2024-01-07 14:28:05


One of the Port Forward settings

  0  
  0  
#2
Options
Re:Port forwarding issue
2024-01-07 14:28:34


  0  
  0  
#3
Options
Re:Port forwarding issue
2024-01-07 16:48:46

  @ChandlerBing 

 

If you forward ALL the ports, it won't forward specific ones.  I would use the DMZ feature as a catchall to forward unspecified ports, and then specific port forwarding rules for each dedicated service port to the other server IPs

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#4
Options
Re:Port forwarding issue
2024-01-07 17:59:38 - last edited 2024-01-07 18:00:03

  @d0ugmac1 
Not sure of the point you are making. I have only forwarded at this point 3 ports. I added the ACL from advice rendered. Are you saying that I am forwarding all ports via the ACL?

  0  
  0  
#5
Options
Re:Port forwarding issue
2024-01-07 18:49:41

  @ChandlerBing 

 

I was confused by the rule you show in post #1.  That is default behaviour so why create a rule and possible problems.  Your second forwarding rule should work, assuming the 192.168.x.x address is completed and points to an active server with those ports active.  If it doesn't work, you need to inspect your WAN interface and verify that it is in fact a public non-NAT'd IP address.  Visit a site like formyip dot com, and validate that the IP presented matches the one assigned to the ER605's WAN interface.

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#6
Options
Re:Port forwarding issue
2024-01-07 20:41:06

  @d0ugmac1 
I deleted the ACL entry and activated the NATDMZ pointing toward the server. No change.

 

  0  
  0  
#7
Options
Re:Port forwarding issue
2024-01-07 20:58:44

  @ChandlerBing 

 

Then it sounds like you don't have a public IP on your WAN from your ISP.

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#8
Options
Re:Port forwarding issue
2024-01-08 04:02:51

  @d0ugmac1 

what would be strange is that the previous router was port forwarding.

  0  
  0  
#9
Options
Re:Port forwarding issue
2024-01-08 13:48:37

  @ChandlerBing 

 

What IP is your ER605 reporting on it's WAN interface?

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#10
Options
Re:Port forwarding issue
2024-01-08 14:32:06

  @d0ugmac1 
It is reporting the public ip according to ipchicken dot com

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 1401

Replies: 13

Related Articles