Missing label (with SSID info) printed at the bottom of the product

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Missing label (with SSID info) printed at the bottom of the product

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Missing label (with SSID info) printed at the bottom of the product
Missing label (with SSID info) printed at the bottom of the product
2024-06-20 20:58:40 - last edited 2024-06-21 03:56:01
Model: EAP110-Outdoor  
Hardware Version:
Firmware Version:

If missing, what to do when you have to enter the required Device Key or Mc information?

File:
IMG_20240620_225143.jpgDownload
  0      
  0      
#1
Options
1 Accepted Solution
Re:Missing label (with SSID info) printed at the bottom of the product-Solution
2024-06-21 03:55:48 - last edited 2024-06-21 03:56:01

  @JeanV 
The device label can be found on the device itself. Because this is an outdoor device, the label has been placed beneath the cover. To get it, remove the unit's small cover. In addition, the Device Key is not required during the setup process. The Device Key is used to set up the controller, not this unit.

We have an article that introduces how to use the Omada app to set it up. Please read it.
How to configure basic wireless settings of my TP-Link EAP in Standalone mode?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
3 Reply
Re:Missing label (with SSID info) printed at the bottom of the product-Solution
2024-06-21 03:55:48 - last edited 2024-06-21 03:56:01

  @JeanV 
The device label can be found on the device itself. Because this is an outdoor device, the label has been placed beneath the cover. To get it, remove the unit's small cover. In addition, the Device Key is not required during the setup process. The Device Key is used to set up the controller, not this unit.

We have an article that introduces how to use the Omada app to set it up. Please read it.
How to configure basic wireless settings of my TP-Link EAP in Standalone mode?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:Missing label (with SSID info) printed at the bottom of the product
2024-06-21 08:36:01

  @Hank21 

Many thanks for your prompt reply.

I now have located the MAC information inside the cover of the EAP110 device. It indicates: A8-42-A1-F1-53-82.

On the Omada application, when I try to enter this code, it shows as A842-A1F1-5382- and the app indicates "Key format of the device not valid" (stated in french as Format de clé de périphèrique non valide) 

Please see attachment.

Could you please explain how to proceed?

 

 

File:
JeanV EAP110.pdfDownload
  0  
  0  
#3
Options
Re:Missing label (with SSID info) printed at the bottom of the product
2024-06-21 09:54:36

  @JeanV 

There is no need to enter the device key. The Mac address is not the device key.You can skip that step and follow the instructions to set up it. Remember to switch to the standalone APs, which are located in the top right corner of the Omada app.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 270

Replies: 3

Related Articles