Business Community > All Threads > problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
< All Threads

problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators

problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators

problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
2024-07-10 10:20:59 - last edited 2024-10-16 08:38:51
Model: EAP670  
Hardware Version: V1
Firmware Version: 1.0.15 Build 20240312 Rel. 77671

 

I have a problem with EAP670 like here 

https://community.tp-link.com/en/business/forum/topic/617924?sortDir=ASChttps://community.tp-link.com/en/business/forum/topic/617924?sortDir=ASC

 

I'm also have successfully installed an EAP670 via a POE switch (TL-SG1008P) by cat 6 cable and all is working well but uplink show only 10 Mbps with Full duplex in Omada 

I tried to reset it via Omada and using button on the EAP670 and also tried reconnet by patch cable 1m - didn’t help anything 

I thied to reset and setup to another Omada network  - didn’t help either  

I have two another EAP670 in the same network  - works fine 1000 Mbps with Full duplex 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators -Solution
2024-07-11 05:49:23 - last edited 2024-10-16 08:38:51

Hi  @Berg-UA 

 

What if swap this EAP670 with another 1000Mbps EAP670?

That is, plug this EAP670 into another known working cable. Will it still keep to negotiate at 10Mbps?

Recommended Solution
  0  
  0  
#2
Options
5 Reply
Re:problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators -Solution
2024-07-11 05:49:23 - last edited 2024-10-16 08:38:51

Hi  @Berg-UA 

 

What if swap this EAP670 with another 1000Mbps EAP670?

That is, plug this EAP670 into another known working cable. Will it still keep to negotiate at 10Mbps?

Recommended Solution
  0  
  0  
#2
Options
Re:problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
2 weeks ago

  @Vincent-TP 

 

We have 24 eap670 and 8 of them are just purely defective. tried to resolve software wise for 2 weeks and nothing. In terms of wiring, we have 24 units. Plug one in and you get 1000, plug the other unit in 100. The units that show 10/100, I can with confidence tell you, dont waste your time or assume, no hope... just exchange it and keep trucking

  1  
  1  
#3
Options
Re:problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
2 weeks ago

  @Vincent-TP  another ane 1000Mbps EAP670 works fine, and now I'm waiting for a response from Service Center about a broken EAP670

  0  
  0  
#4
Options
Re:problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
2 weeks ago

  @Vincent-TP And also I tried to put this one 6e cat cable to another one POE Port in TP-Link SG2218P - result the same only 10 Mbps

  0  
  0  
#5
Options
Re:problem with EAP670 uplink show only 10 Mbps with Full duplex in Omada and on TL-SG1008P indicators
2 weeks ago

  @Berg-UA 

 

Then getting a replacement may be the fastest way.

  1  
  1  
#6
Options

Information

Helpful: 0

Views: 216

Replies: 5

Related Articles
2.5gbps uplink on EAP670 speed not as expected
1458 0
EAP670 only connects as Mesh (uplink) not wired
688 0
EAP670 making DNS A and AAAA queries for host eap670 every 10 minutes
74 0
EAP670 and EAP653 EU
2025 0
Difference between EAP670 and EAP673?
3246 0
EAP670 Speeds Below Expectations
1795 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.