Switches
Early AccessOmada IES_Series Pre-Release Firmware for SDN Controller 6.3.0 (Released on Sep 28th, 2026)
This Article Applies to IES206G(UN) 1.0 IES206GPP(UN) 1.0 IES208G(UN) 1.0 IES210GPP(UN) 1.0 Note: To upgrade to this version, first upgrade the switch firmware to the following intermediate version: I
By
Nathan-TP
Nathan-TP0Helpful
378Views
Early AccessSG3452X SG3452XMPP Pre-Release Firmware for SDN Controller 6.4 (Released on Sep 24th, 2026)
This Article Applies to a) SG3452X(UN) v1.20 b) SG3452X(UN) v1.30 c) SG3452XMPP(UN) v1.20 Release Notes New Features: Added support for the next-generation network operating system FEP 2.0 platform, f
By
Nathan-TP
Nathan-TP0Helpful
484Views
This Article Applies to a) SX6632YF(UN) v1.0 b) SX6632YF(UN) v1.6 c) SX6632YF(UN) v1.20 d) SX6632YF(UN) v1.26 Release Notes New Features: Add support for PTP (Precision Time Protocol) and IEEE 802.1AS
By
Nathan-TP
Nathan-TP0Helpful
593Views
Early AccessESxxx-M2 V1 Pre-Release Firmware Fully Adapted to SDN Controller 6.3.0 (Updated on Sep 3rd, 2026)
This Article Applies to ES206X-M2 (UN) V1.0 ES210XPP-M2(UN) V1.0 ES206XPP-M2(UN) V1.0 ES210X-M2(UN) V1.0 Note: To upgrade to this version, first upgrade the switch firmware to the following intermedia
By
Vincent-TP
Vincent-TP0Helpful
1284Views
Hello, I have configured 802.1x authentication on my switches. First the 802.1x authentication is successful. Then the client reboots. During the reboot there is a network disconnect. Then 802.1x auth
VLAN & Multi-Networks802.1x
0Helpful
299Views
Hi. I have the problem, that I once applied port security rules (MAC binding number allowed 1) to several port of my switch via omada cli command. It worked great, but now the setup changed, so I remo
By
SebastianH
· Latest post Yesterday
by SebastianH
0Helpful
184Views
Setting up a surveillance system is not just about wiring cameras and connecting them to your network. You’d want to prevent just anyone from accessing your camera feeds to protect your privacy, a hig
3Helpful
929Views
I've had two brand new SG345P switches that keep showing Fan Was Error messages. First one was returned and the replacement has done the same immediately from install. Any one else had this ? I'm fair
PoEHealth
By
TopBanana
0Helpful
81Views
Hi everyone, I'm setting up my home network inside my apartment's main communication box and I'm facing a physical constraint: there are no power outlets available inside the enclosure, and absolutely
helpPresales
By
RodrigoTomeES
· Latest post Thursday
by NeilR_M
0Helpful
147Views
Good Day, I recently purchased an ES210X-M2 switch, upon adopting it in the software controller (windows based) I am unable to see the IP addresses with the devices connected to the switch. I only see
TopologyControllerConfiguration
9Helpful
2060Views
Guys I am having some "hangs" to use a better word for them, and noticed that a SG3452 switch shows port errors. How can I find which port it is reporting - it seems to just show that "1" was in error
Network ConnectivityTopologyVLAN & Multi-Networksfaulty switch port
0Helpful
160Views
Howdy, I have some new switches of this model, and for some reason that i'm unable to understand, the sfp's are unable to operate at 10gbit, they dont even link to each other, i only have link if i fo
SFP
By
JorgeBastos
· Latest post a week ago
by JorgeBastos
0Helpful
212Views